Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 46

Symptom:

P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELA-
TION

When Monitored and Set Condition:

P0068-MANIFOLD PRESSURE/THROTTLE POSITION CORRELATION

When Monitored:

With the engine running and no MAP Sensor or TP Sensor DTC’s set.

Set Condition:

The PCM determines a valid range in which the TP Sensor should be, at

a given RPM/Load. The actual TP Sensor voltage is then compared to this value. If the TP
Sensor voltage does not fall within the expected range within a predetermined time an
error will be detected. Two Trip Fault.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

HIGH RESISTANCE IN MAP (K6) 5 VOLT SUPPLY CIRCUIT

RESISTANCE TO GROUND IN MAP (K6) 5 VOLT SUPPLY CIRCUIT

MAP SENSOR

HIGH RESISTANCE IN (K1) MAP SIGNAL CIRCUIT

RESISTANCE TO GROUND IN (K1) MAP SIGNAL CIRCUIT

HIGH RESISTANCE IN (K4) MAP GROUND CIRCUIT

PCM

TP SENSOR OPERATION

HIGH RESISTANCE IN TP SENSOR (K6) 5 VOLT SUPPLY CIRCUIT

RESISTANCE TO GROUND IN TP SENSOR (K6) 5 VOLT SUPPLY CIRCUIT

TP SENSOR

HIGH RESISTANCE IN (K22) TP SIGNAL CIRCUIT

RESISTANCE TO GROUND IN (K22) TP SENSOR SIGNAL CIRCUIT

HIGH RESISTANCE IN TP (K4) SENSOR GROUND CIRCUIT

PCM

40

DRIVEABILITY - NGC

«
...
44
45
46
47
48
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов