Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 41

Страница: 41 / 370

Symptom List:

P0031-O2 SENSOR 1/1 HEATER CIRCUIT LOW
P0037-O2 SENSOR 1/2 HEATER CIRCUIT LOW

Test Note:

All symptoms listed above are diagnosed using the same tests.

The title for the tests will be P0031-O2 SENSOR 1/1 HEATER
CIRCUIT LOW.

When Monitored and Set Condition:

P0031-O2 SENSOR 1/1 HEATER CIRCUIT LOW

When Monitored:

Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is

on.

Set Condition:

The PCM detects the O2 Heater voltage is out of acceptable range. Below

0.0926 of a volt. One Trip Fault.

P0037-O2 SENSOR 1/2 HEATER CIRCUIT LOW

When Monitored:

Battery voltage above 10.6 volts, ASD is powered up, and O2 heater is

on.

Set Condition:

The PCM detects the O2 Heater voltage is out of acceptable range. Below

0.0926 of a volt. One Trip Fault.

POSSIBLE CAUSES

O2 SENSOR HEATER OPERATION

O2 HEATER ELEMENT

O2 HEATER CONTROL CIRCUIT

O2 HEATER CONTROL SHORTED TO GROUND

PCM

TEST

ACTION

APPLICABILITY

Ignition on, engine not running.
With the DRBIII

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

Go To

→

Go To

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Результаты поиска

Содержание Pacifica CS 2004

Отзывы:

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 41 / 370

Результаты поиска

Содержание Pacifica CS 2004

Отзывы: