manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 106 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 106

Symptom:

P0171-FUEL SYSTEM 1/1 LEAN

When Monitored and Set Condition:

P0171-FUEL SYSTEM 1/1 LEAN

When Monitored:

With the engine running in closed loop mode, the ambient/battery

temperature above (-7°C)20°F, altitude below 8500 ft and fuel level greater than 15%.

Set Condition:

If the PCM multiplies short term compensation by long term adaptive and

a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates
and a trouble code is stored.

POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO

RESTRICTED FUEL SUPPLY LINE

FUEL PUMP INLET STRAINER PLUGGED

FUEL PUMP MODULE

O2 SENSOR

O2 SIGNAL CIRCUIT

O2 RETURN CIRCUIT

O2 SENSOR HEATER OPERATION

THROTTLE POSITION SENSOR SWEEP

MAP SENSOR OPERATION

ECT SENSOR OPERATION

ENGINE MECHANICAL PROBLEM

FUEL CONTAMINATION/EXHAUST LEAK

TEST

ACTION

APPLICABILITY

1

NOTE: Check for contaminants that may have damaged the O2 Sensor:
contaminated fuel, unapproved silicone, oil and coolant.
NOTE: Diagnose any Misfire DTC(s) first, if set along with the fuel system
DTC.
Ignition on, engine not running.
With the DRBIII

t

, read DTCs and record the related Freeze Frame data.

Is the Good Trip Counter displayed and equal to zero?

All

Yes

→

Go To

2

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

100

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов