Chrysler Concorde 1993, Руководство по обслуживанию, Страница: 368 / 820

is a second transmitter it has to be set at this time.
Press any button on the second transmitter and wait
for the locks to cycle.
(5) Disconnect the program line from ground. This
returns the system to its normal operation mode.
(6) Replace middle vent bezel, to the instrument
panel.
HORN CHIRP CANCELLATION
During the programming operation the horn chirp
can be disabled using the following procedures:
(1) Remove the middle vent bezel from the instru-
ment panel and locate the traction control black con-
nector.
(2) Turn ignition switch to the ON position.
(3) Ground pin 4 of the traction control connector
(Fig. 5). This is the programming line for the Remote
Keyless Entry Module. The door locks will lock and
unlock, to indicate the receiver is ready to receive
transmitter code. The trunk solenoid will not cycle at
this time.
(4) Press any button on the transmitter to set code.
The locks will cycle to confirm programming. If there
is a second transmitter it has to be set at this time.
Press any button on the second transmitter and wait
for the locks to cycle.
(5) Press any button on the transmitter to set code.
If there is a second transmitter it has to be set at
this time. The locks will cycle with each transmitter
to confirm programming.
(6) Using one of the transmitter, press the trans-
mitter LOCK then UNLOCK buttons, repeat three
times.
(7) Door locks and trunk release will cycle three
times as feedback of Horn Chirp Lockout.
(8) Disconnect the program line from ground. This
returns the system to its normal operation mode.
(9) Attach the connector back to its original posi-
tion. Install the upper center bezel to the instrument
panel.
(10) To reinstate the Horn Chirp feature, simple
reprogram the module. Refer to Programing Remote
Keyless Entry Transmitter
REMOTE KEYLESS ENTRY SYSTEM TEST
CIRCUIT BREAKER
Find Remote Keyless Entry circuit breaker on fuse
block. Pull out slightly, but maintain contact be-
tween the circuit breaker terminals and the termi-
nals in fuse block. Connect the ground probe of the
voltmeter to a good ground. Using the positive probe
of the voltmeter, check both terminals of circuit
breaker for battery voltage. If only one terminal
measures battery voltage, the circuit breaker is de-
fective and must be replaced. If neither terminal
shows battery voltage, check for open or shorted cir-
cuit to circuit breaker.
CONDITION: WHEN TRYING TO PROGRAM
THE RECEIVER MODULE IN THE VEHICLE
WITH A NEW TRANSMITTER AND THERE IS
NO RESPONSE FROM THE MODULE,
EXAMPLE: THE DOOR LOCKS DO NOT CYCLE
THROUGH A LOCK/UNLOCK ROUTINE. REFER
TO FIG. 6 FOR A BLOCK WIRING DIAGRAM OR
TO GROUP 8W, WIRING DIAGRAMS.
(1) Activate the power door lock switches to ensure
that the lock and unlock relays and the door motors
are functioning. Check the batteries in the transmit-
ter.
(2) Check that the module has a battery voltage at
cavity 8 of the black connector from fuse #13. Other
modules that would be affected are; the interior
lamps and the radio/clock memory.
(3) Be sure that the module has an ignition feed at
cavity 2 of the blue connector from fuse #14. Also af-
fected would be the body computer, instrument clus-
ter and message center.
(4) Check that cavity 4 on black connector is
grounded to the front center floor panel, driver side,
by the passive restraint bracket, refer to Group 8W,
wire diagrams.
(5) Check that the programming wire is properly
grounded. Check cavity 5 (program line) of the black
connector and cavity 4 of the black traction control
connector.
(6) If the above circuits are good, replace the re-
mote keyless entry module.
CONDITION: ALL DOORS EXCEPT DRIVER’S
DOOR WILL LOCK WITH THE TRANSMITTER.
(1) Test cavity 3 of the black connector for ground.
(2) If there is no ground at the pin, replace the re-
mote keyless entry module.
(3) If there is a ground at the output, replace the
door lock motor.
CONDITION: ONLY DRIVER’S DOOR WILL
LOCK WITH THE TRANSMITTER.
(1) Check for ground circuit to unlock relay. If no
ground repair as necessary.
(2) Replace unlock relay
CONDITION: DOORS DO NOT LOCK WITH THE
TRANSMITTER, BUT STILL GET HORN CHIRP
THAT INDICATES THAT THEY DID LOCK.
(1) Using a voltmeter, ground the negative probe
and insert the positive probe into cavity 6 of the
black connector. Press the lock button on the trans-
mitter. Wait for quick voltage pulse. It may be nec-
essary to press the transmitter several times since
the pulse will only appear for a couple of millisec-
onds. If no voltage pulse is measured, replace remote
keyless entry module.
8P - 4 POWER LOCKS