manualshive.com logo in svg

Chrysler 300 Touring RWD 2010, Руководство пользователя

Поделиться
Скачать
Chrysler 300 Touring RWD 2010 Скачать руководство пользователя страница 485

CAUTION!

•

It is essential when replacing the cables on the

battery that the positive cable is attached to the

positive post and the negative cable is attached to

the negative post. Battery posts are marked positive

(+) and negative (-) and are identified on the

battery case. Cable clamps should be tight on the

terminal posts and free of corrosion.

•

If a “fast charger” is used while the battery is in the

vehicle, disconnect both vehicle battery cables be-

fore connecting the charger to the battery. Do not

use a “fast charger” to provide starting voltage.

Air Conditioner Maintenance

For best possible performance, your air conditioner should

be checked and serviced by an authorized dealer at the start

of each warm season. This service should include cleaning of

the condenser fins and a performance test. Drive belt tension

should also be checked at this time.

WARNING!

•

Use only refrigerants and compressor lubricants
approved by the manufacturer for your air condi-
tioning system. Some unapproved refrigerants are
flammable and can explode, injuring you. Other
unapproved refrigerants or lubricants can cause the
system to fail, requiring costly repairs. Refer to
Warranty Information Book, located on the DVD,
for further warranty information.

•

The air conditioning system contains refrigerant
under high pressure. To avoid risk of personal
injury or damage to the system, adding refrigerant
or any repair requiring lines to be disconnected
should be done by an experienced technician.

7

MAINTAINING YOUR VEHICLE 483

Содержание 300 Touring RWD 2010































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды