manualshive.com logo in svg

Chromalox MiniMax 1, Руководство пользователя, Страница: 27 / 28

Поделиться
Скачать
Chromalox MiniMax 1 Скачать руководство пользователя страница 27

- 25 -

© 2021 Chromalox

®

, Inc.

1-888-996-9258

Model 

SCR Power Pack

Mmax2

3 Phase SCR Power Controller complete with Lugs and I2T Fusing

1, 2

Code Control Configuration

5

Proportional Control, DOT Zero-Crossover Firing, Command Input Signals: 4-20mA, 0-5 

VDC, 1-5 VDC (via Modbus RTU/485 only), 0-10 VDC, Remote 0-1000 OHM Potentiometer 

w/Manual Override, Modbus RTU/RS485 Communications. RTD Heat Sink Temperature 

Sensor with Two Set-Points, Automatic Line Sensing 50/60HZ, Remote Permissive Stop 

Input, Form “C” Dry Contact Alarm Output, Staged Heating w/Digital Calibration Zero / 

Span Adjustments(4-8 mA, 8-12 mA,12-16 mA,16-20 mA (via Modbus RTU/RS485 only), 

LED Diagnostics: Command Input, Main/Trigger Boards  Running, SCR Status per Phase,  

Diagnostic Kit via Modbus RTU/RS485: Highest Heat Sink Temperature, Last Heat Sink 

Temperature, Highest and Lowest Ambient Temperature, Line Frequency Monitoring, 

Third Party Certifications: UL, cUL, CE, DEMKO (650 A and below).

Code   Current at 50˚C (104˚F) Ambient

01

  30 Amp

02

  50 Amp

03

  75 Amp

Code Line Voltage

1

120 - 480 Vac

2

575 Vac

Code Instrument Power

1

120 to 240Vac 50/60Hz

Code Remote Manual A`djust/Auto Manual Switch

3

0

None

1

Pot with 0-100% dial and local/Remote Switch, 

Single Turn 1K ohm Potentiometer

(Requires Proportional Board)

Mmax2  -

5

01

1

1

 0

Typical Model Number  

1)  SCR fusing is for semiconductor protection only, not wire protection.

2)  Supplied loose for customer mounting. 575V fusing only

3)  Supplied loose for customer mounting.

Note:
Storage Temperature 14ºF to 158ºF (-10ºC to 70ºC). 

CE Application requires filters.

Chromalox Part Numbers
0005-60056 — Line filter, three phase, 440VAC

0005-60057 — Line filter, 120-230VAC
CE application requires filter.

MiniMax 2 Ordering Information

Содержание MiniMax 1





























Отзывы:

Нет отзывов