Chromalox MiniMax 1 Скачать руководство пользователя страница 21

- 19 -

© 2021 Chromalox

®

, Inc.

1-888-996-9258

6

Maintenance

Connections – Loose connections in the power wiring will generate hot spots. These will cause degradation 
of electronic equipment. Periodic inspections should be made to ensure that connections are secure and 
that there are no signs of excessive heating such as discoloration, and so on.

Corrosion – If the power module is installed in an environment with high humidity or dampness, electrical 
connections may suffer corrosion. Periodically check the power module for corrosion.

Damage – Periodically check for rodent damage to wiring and other components.

Filters – Many high-powered control enclosures rely on blowers or fans to maintain a safe operating temper-
ature. The filters used with these devices should be changed on a periodic basis to insure adequate enclo-
sure cooling is maintained.

Dust – Periodically check for dust or other particulate buildup on heatsinks and bus bars.

READ AND UNDERSTAND BEFORE 

CARRYING OUT THE WORK DETAILED BELOW

WARNING

HAZARDOUS VOLTAGE: Disconnect all power before perform-

ing any maintenance or examining the power module. Ex-

posed terminals may carry LETHALLY HIGH VOLTAGES when 

power is applied.

Содержание MiniMax 1





























Отзывы: