Chromalox MiniMax 1 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 28

Chromalox MiniMax 1 Скачать руководство пользователя страница 10

- 8 -

© 2021 Chromalox

®

, Inc.

1-888-996-9258

4.2 - Step 2: Wiring

Careful attention must be paid when attaching the wiring to the MiniMax to ensure proper and safe opera-
tion. This section contains detailed information on how to connect the power, resistive load, ground, and
command signal wiring.

IMPORTANT: Select installation wiring that is in accordance with the National

Electrical Code and any local standards that may be applicable.

WARNING

HAZARDOUS VOLTAGE: Only qualified personnel should per-

form electrical wiring for the MiniMax Power Paks. LETHALLY

HIGH VOLTAGES are associated with this equipment and are

dangerous if improperly installed.

WARNING

The following wiring instructions are for the Digital Minimax

only. If using Analog Minimax, contact factory for appropriate

wiring schematics. Analog Minimax is designated as MMAXI, II,

or III followed by the number 1, 2, 3, or 4 under the firing mode.

4.2.1 - Power/Load Wiring

The following illustrations depict how to connect the MiniMax to a resistive or inductive load. Make sure you
refer to the correct illustration for the MiniMax series you have purchased.

MINIMAX1

L2

L1

X1

Single Phase

Resistive

L2 Connection is

NOT on MiniMax

«
...
8
9
10
11
12
...
»

Содержание MiniMax 1





























Отзывы:

Нет отзывов