manualshive.com logo in svg

Chromalox IntelliTrace ITC 2, Руководство по установке и эксплуатации, Страница: 9 / 32

Поделиться
Скачать
Chromalox IntelliTrace ITC 2 Скачать руководство пользователя страница 9

9

Navigating the ITC

Visually, here is how one navigates through the ITC Menus & Parameters:

The horizontal security level bars, which are above the 
ITC Menu & Parameter navigation map, illustrate the 
available menus within that security level. The Main Win-
dow is presented when the 

 button is selected 

while the operator is at the last available menu screen 
within the current security level. 

Security Level 3
Security Level 2
Security Level 1

2. Login

6. Comms Menu 

7. System Menu 

4. Current Menu 

3. Temperature Menu

5. Control Menu

1. Main Window

Mode

Logged?

Correct?

No

No

Yes

Yes

Mode

Mode

Mode

Mode

Mode

Temp Setpoint 1 

Lo Temp Alarm 1 

Hi Temp Alarm 1 

Temp Setpoint 2 

Lo Temp Alarm 2 

Hi Temp Alarm 2

Failed Sensor

Output 2

Password Level 1 

Password Level 2 

Password Level 3 

Alarm State

Restore to Default 

Lo Current Alarm 1 

Hi Current Alarm1 

GFEP Setpoint 1 

GFEP Alarm/Trip 1 

Lo Current Alarm 2

Hi Current Alarm 2 

GFEP Setpoint 2 

GFEP Alarm/Trip 2 

Baud Rate 

Parity 

Modbus ID 

IP Address 

DHCP

Firmware Version 

Button Sound 

Units 

Temp. Sensing 1 

Temp. Sensing 2 

Failed Sensor

Output 1 

Mode

Curved Double Arrow - continuation path for 1-Circuit Units Only

Dashed Parameter Ovals appear on 2-Circuit Units Only

Dashed, Angled Connector - continuation path for 2-Circuit Units Only

Mode arrow represents pressing the MODE Key

GFEP Alarm/Trip 2 

Auto Control Mode 1 

Auto/Man/Off 1 

Deadband 1 

Autotune 1 

Prop. Band 1

Integral 1 

Rate 1 

Soft Start 1 

Manual Offset 1

Auto Control Mode 2 

Auto/Man/Off 2 

Deadband 2 

Autotune 2 

Prop. Band 2

Integral 2 

Rate 2 

Soft Start 2 

Manual Offset 2

Содержание IntelliTrace ITC 2

































Отзывы:

Нет отзывов