manualshive.com logo in svg

Chromalox IntelliTrace ITC 2, Руководство по установке и эксплуатации, Страница: 32 / 32

Поделиться
Скачать
Chromalox IntelliTrace ITC 2 Скачать руководство пользователя страница 32

32

Service Contact 
Information

Chromalox is a global supplier, providing the highest 

level of customer support. If you should have questions 

concerning your intelliTRACE™ ITC Controller or need 

information, you may contact Chromalox at:

Corporate Headquarters 

Chromalox, Inc.

103 Gamma Drive

Pittsburgh, PA 15238 

Phone: (412) 967-3800 

Customer Service Hotline:  1-800-443-2640

For application questions, you can:
1.  Call one of our application engineers for personal 

assistance at 1-888-996-9258.

2.  Visit the technical reference section of our website 

at www.chromalox.com for downloadable manuals 

in PDF format.

Limited Warranty:

Please refer to the Chromalox limited warranty applicable to this product at

http://www.chromalox.com/customer-service/policies/termsofsale.aspx.

Chromalox, Inc.

1347 Heil Quaker Boulevard

Lavergne, TN 37086

(615) 793-3900

www.chromalox.com

© 2018 Chromalox, Inc.

Содержание IntelliTrace ITC 2

































Отзывы:

Нет отзывов