manualshive.com logo in svg

Chromalox IntelliTrace ITC 2, Руководство по установке и эксплуатации, Страница: 24 / 32

Поделиться
Скачать
Chromalox IntelliTrace ITC 2 Скачать руководство пользователя страница 24

24

Alarms

Alarm Types 

Low & High Temperature, Low & High Current, High GFEP, 

Sensor Failure 

Alarm Relays 

1 x DC Alarm Output, 1.8 Amp, Customer Supplied 0 - 50 VDC 

1 x AC Alarm Output, 1.8 Amp, Customer Supplied 12-240 VAC

Alarm Contact State 

Mode 

Default

Optional

Normal Operation

Closed

Open

Alarm Condition

Open

Closed

Power Off

Open

Open

Communications

ModBus 

RTU/RS485  (2 or 4 wire) & RTU/RS422, TCP/Ethernet

Baud Rate, Hz 

2400, 4800, 9600, 19200, 38400, 56000 

Parity 

Range: Even, Odd, None 

ModBus ID 

Range: 1 – 255 

DHCP

Range: Use, Do Not Use

Ethernet IP

Webserver over Ethernet 

Operating & Environmental

Temperature 

 -40˚F to 104˚F (-40˚C to 40˚C) 

Humidity

Relative Humidity 0% to 90%

Power Supply 

100-277 Vac 50/60Hz

Protection 

IEC IP66 

Enclosure Rating 

NEMA 4X FG 

Approvals 

UL/cUL Ordinary and Class I, Division 2, Groups A,B,C,D Hazardous loca-

tions (UL file Number: E347725), CE

Temperature Rating

T4

Содержание IntelliTrace ITC 2

































Отзывы:

Нет отзывов