Chromalox CX224 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 17

Chromalox CX224 Скачать руководство пользователя страница 2

Chromalox Tel: 615-793-3900 • Fax: 615-793-3563 • www.chromalox.com

2

1.

Introduction

This setup tutorial will step through some of the main ways that the CX224 can be
used. After completion, the user will have a good understanding of the features and
how to use them. Each section will build off of the one before it.S

Buttons

Scrolling through Zones

Main Menu

Sub Menu

Back

Returns to

monitor zones

Returns to

previous step

Forward Up

Changes

current value

in step

Back Down

Scrolls through

current step

Forward

Enters into

selected menu

option

Goes to next

step

Table 1 Quick Reference Guide

Note:

Holding down any button for 3 seconds and you will be put into the main

menu.

2. Configuring Controller for Operation

Example 1: Over Temp Operation with Hysteresis @ 5

º

F

1.

Begin by placing the CX224 on a desk or table.

2.

Connect one senor to the unit, note which type of sensor you have connected.

3.

Apply power to the CX224. The display should light and the message “Initializing
Inputs” will be displayed. A few seconds later the unit will display “Zone 1 Off”.

4.

Press and hold any one of the keys on the front panel until the main menu is
displayed. This will take about 3 seconds.

5.

Move the cursor to 2. “Configuration”, then press Enter.

6.

Select 1. “Change Passwords” and press Enter.

7.

Select “Yes” by pressing the up arrow, then Enter.

http://www.chromalox.com

«
1
2
3
4
...
»

Содержание CX224


















Отзывы:

Нет отзывов