manualshive.com logo in svg

Chromalox Chroma-FP-OD Series, Инструкция по установке и эксплуатации, Страница: 9 / 20

Поделиться
Скачать
Chromalox Chroma-FP-OD Series Скачать руководство пользователя страница 9

P01 - Temperature set point

Move DIP switch S1 located on the side of thermostat to ON position.
“P01” and the temperature set point will appear on display.
Use the [+] and [-] buttons to adjust the temperature set point.

Range: 14…77°F / -10…+25°C, Default: 37°F / 3°C

As long as the ambient temperature is lower than the temperature 
set point P01, the Chroma-FP-OD will turn ON. 

Pg. 9

Technician settings

Use the technician settings mode to view and adjust the following parameters:

Disconnect power and open the internal door by releasing the two screws.
Move DIP switch S1 located on the side of thermostat to ON position.

Press the [SELECT] and [+] buttons simultaneously to move forward to the next 
technician parameter.
Press the [SELECT] and [-] buttons simultaneously to return to the previous 
technician parameter.

Enter technician settings mode

Enter technician 

settings mode

Important: Changes made to technician parameters will not take effect as 
long as DIP switch S1 is in ON position.

Save changes 

and exit 

technician 

settings mode

Parameters:

Save changes and exit technician settings mode

Move DIP switch S1 located on the side of thermostat to OFF position.

Temperature

set point

P01

Temperature set point

P02

Lower ambient temperature limit to stop 
the heater

P03

Time delay before stopping the heater

P04

ON time for manual mode

P05

Heaters cycle time / Splitting time

P06

Enable/Disable 2

nd

 temperature sensor 

logic (Aquastat)

P08

MAC Address for BMS 
and for Master-Slaves

P09

Commissioning / Test mode

P11

Master/Slave

P15

Temperature sensor calibration Offset

Restore defaults

Chroma-FP-OD Series

Owner’s manual & Technician Settings

1-800-443-2640

www.chromalox.com

Содержание Chroma-FP-OD Series





















Отзывы:

Нет отзывов