Chromalox Chroma-FP-OD Series Скачать руководство пользователя страница 3

Страница: 3 / 20

Introduction

The Chroma-FP-OD Series power boxes offer smart and easy control for HEAT TRACING SYSTEMS.
It can operate one heating zone.
Typical applications include pipes, valves or tanks.

The backlit LCD screen provides full interface and information to the system status.

The Chroma-FP-OD offers various operating and programming options such as:
- Switchable temperature scales (°F or °C)

- Adjustable Lower ambient temperature limit to stop

- Both Automatic and Manual modes

heater (lockout)

- Energy saving temperature limit

- Commissioning/Test environment

- Adjustable heater hold on off delay

Pg. 3

Temperature sensor

Chroma-FP-OD

Operating panel

Chroma-FP-OD General system layout

Zone 1

Aquastat sensor (option)

Pipe
Sensor
Heater

Chroma-FP-OD Series

Owner’s manual & Technician Settings

1-800-443-2640

www.chromalox.com

Содержание Chroma-FP-OD Series





















Результаты поиска

Содержание Chroma-FP-OD Series

Отзывы:

Chromalox Chroma-FP-OD Series, Инструкция по установке и эксплуатации, Страница: 3 / 20

Результаты поиска

Содержание Chroma-FP-OD Series

Отзывы: