Chromalox Chroma-FP-OD Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 20

Chromalox Chroma-FP-OD Series Скачать руководство пользователя страница 11

Technician settings (Cont’)

Pg. 11

P05 – Not in use

Cont’

P06 – Enable/Disable Temperature sensor / Aquastat logic

Press the [SELECT] and [+] buttons simultaneously.
“P06” and the number “0” or “1” will appear on display.
Use the [+] and [-] buttons to select between:

“0” - Logic set by both TEMPERATURE SENSOR

and AQUASTAT (default).

“1” - Logic set by TEMPERATURE sensor only.
“2” - Logic set by AQUASTAT sensor only

(The display will not show the temperature)

Logic by

temperature

sensor only

Logic by

temperature

sensor and

aquastat

Logic by aquastat

sensor only

Press the [SELECT] and [+] buttons simultaneously.
“P05” will appear on display.
Proceed to P06.

P04 - Manual mode ON time

Press the [SELECT] and [+] buttons simultaneously.
“P04”, “On” and the “Manual ON” mode time period will appear on display.

The time frame in which the heaters remain ON after receiving an “Manual
ON” command.

Use the [+] and [-] buttons to adjust the “Manual ON” time (Hours).

Range: 1...99 hours

Default: 4 hours

Press the [SELECT] and [+] buttons simultaneously again.
Use the [+] and [-] buttons to adjust the “Manual ON” time (Minutes).

Range: 0...59 minutes

Default: 0 minutes

Manual ON

(hours)

Manual ON

(minutes)

Chroma-FP-OD Series

Owner’s manual & Technician Settings

1-800-443-2640

www.chromalox.com

«
...
9
10
11
12
13
...
»

Содержание Chroma-FP-OD Series





















Отзывы:

Нет отзывов