Chromalox 1601 Скачать руководство пользователя страница 27

Страница: 27 / 32

GENERAL INFORMATION

GENERAL SPECIFICATIONS
Case

ABS grey color (RAL 7043); self-extinguish-
ing degree: V-0 according to UL 94.

Front protection

- designed and tested for IP 65 (*)

and NEMA 4X (*) for indoor locations (when panel
gasket is installed).
(*) Test were performed in accordance with CEI 70-
1 and NEMA 250-1991 STD.

Installation

: panel mounting by means of mounting

braket. Instrument removable from case.

Rear terminal block

:10 screw terminals ( screw

M3, for cables from

0.25 to

2.5 mm

or from

AWG 22 to AWG 14 ) with connection diagrams
and safety rear cover.

Dimensions

: 48 x 48 mm, depth 100 mm (DIN

43700).

Weight

: 160 g max.

Power supply

- 100V to 240V AC 50/60Hz (-15% to + 10% of the
nominal value).
- 24 V AC/DC (+ 10 % of the nominal value).

Power consumption

: 6 VA max.

nsulation voltage

: 2300 V rms according to

EN 61010-1.

Display updating time

: 500 ms.

Sampling time:

500 ms.

Resolution

: 30000 counts.

Accuracy

(@ 25 °C): +0.3% of the input span +1 °C.

Common mode rejection

: 120 dB at 50/60 Hz.

Normal mode rejection:

60 dB at 50/60 Hz.

Electromagnetic compatibility and safety
requirements

: This instrument is marked CE.

Therefore, it is conforming to council directives
89/336/EEC (reference harmonized standard
EN-50081-2 and EN-50082-2) and to council
directives 73/23/EEC and 93/68/EEC (reference
harmonized standard EN 61010-1).

Installation category

: II

Temperature drift

: < 200 ppm/°C (RJ excluded)

< 400 ppm/°C for RTD input with -19.9/99.9 °C range
and TC type T.

Reference junction drift

: 0.1 °C/°C.

Operative temperature

: from 0 to 50 °C (32 to

122°F).

Storage temperature :

-20 to +70 °C (-4 to 158°F).

Humidity

: from 20 % to 85% RH, non condensing.

Protections

1) WATCH DOG circuit for automatic restart.
2) DIP SWITCH for protection against tampering
of configuration and calibration parameters.

INPUTS
A) THERMOCOUPLE
Type

: L, J, K, N, T programmable by front

pushbuttons.

Line resistance

: max. 100

with error <+0.1% of

the input span.

Engineering unit

: °C or °F programmable.

Reference junction

: automatic compensation

from 0 to +50 °C.

Reference junction drift

: 0.1 °C/°C.

Burn-out

: Up or down scale selectable.

Calibration

: according to IEC 584-1 and DIN

43710 - 1977 (TC L)
STANDARD RANGES TABLE

type

0 - +800 °C

0 - +999 °C

0 - + 400 °C

Measuring ranges

0 - +999 °F

0 - +752 °F

1601-1-0C.p65

5/2/00, 1:45 PM

Содержание 1601

































Результаты поиска

Содержание 1601

Отзывы:

Chromalox 1601, Руководство пользователя, Страница: 27 / 32

Результаты поиска

Содержание 1601

Отзывы: