Chromalox 1601 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 32

Chromalox 1601 Скачать руководство пользователя страница 14

9

P14 -Display of the operator parameters.

This parameter is available only if P11 is different
from 0.
This parameter allows you to enable/disable the
display of the protected parameters during
"operator mode".
OFF = protected parameters cannot be displayed
ON = protected parameters can be displayed

P15 - SMART function enabling/ disabling

0 = The SMART function is disabled
1 = The SMART function enabling/disabling is

NOT protected by the security code (P11).

2 = The SMART function enabling/disabling is

protected by the security code (P11).

P16 - Maximum value of the proportional band
settable by the SMART function

This parameter may be programmed from P17or
P18 value to 99.9.

P17 - Minimum value of the proportional band
settable by the SMART function in heating
control only.

It may be programmed from 1.0% to P16 value.

P18 - Not Available

P19 - Not Available

P20 - Minimum value of integral time settable
by SMART function.

P20 is programmable from 00.1 (10 seconds) to
02.0 (2 minutes).

P21 = Extension of the anti-reset-wind up

Range: from -30 to +30 % of the proportional
band.

NOTE

: a positive value encreases the high limit of

the anti-reset-wind up (over set point) while a
negative value decreases the low limit of the anti-
reset-wind up (under set point).

The advanced configuration procedure is
completed and the instrument shows " CnF" on
the display.
Pressing the "FUNC" will return the unit to the first
configuration parameter.

1601-1-0C.p65

5/2/00, 1:45 PM

9

«
...
12
13
14
15
16
...
»

Содержание 1601

































Отзывы:

Нет отзывов