manualshive.com logo in svg

Chroma 19032-P, Быстрый старт

Поделиться
Скачать
Chroma 19032-P Скачать руководство пользователя страница 33

Electrical Safety Analyzer 19032-P Quick Start Guide

 

19 

S1: T

 test setting in   

S2: 

ited with COM, recall/read test setting in   

S3: 

d with COM, recall/read test setting in   

(10) 9Pin

-Sub connector functions are the same 

r socket and fuse holder. 

AC power, which the 

his 

(12) GND Term

ety GND terminal, please use adaptable implement 

 

 

 

wer cable, please confirm power that use firstly 

urning on power, please peruse “Chapter 3 – Precaution before 

e analyzer will self-test.    If there is abnormal 

specification 125V AC current is lower than 1A.   

he terminal is short-circuited with COM, recall/read

the first group memory.   

The terminal is short-circu

the second group memory. 

The terminal is short-circuite

the third group memory. 

 Connector: 

All of 9 pin D

as (9) Remote I/O. 

(11) AC LINE: 

AC powe

A tri-cord power and fuse holder.    Input 
analyzer is needed from AC power socket.    The detailed 
specification of using fuse please refers “Chapter 3 –  
Precaution before Use” or descriptions of rear panel in t
manual. 

inal: 

Saf

to connect this grounding terminal actually.    If there is 
no grounding actually, the circuit with GND terminal or 
other instruments connecting cable with GND terminal 
is short circuit.    The cover of analyzer may exist high 
voltage.    This is very dangerous, anyone touch the 
analyzer under the above status may cause damage. 
Therefore, it is necessary to connect safety GND 
terminal to ground.

 

 

4.3 

Notice Items and Procedures before 

Operating 

1.  Before plugging AC po

and description of rear panel is match or not and power switch is OFF 
status. 

2.  Before t

Use” and remember it. 

3.  When turns on power, th

condition, please turns off switch and pulls off power cord immediately. 

 
 

Содержание 19032-P
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды