manualshive.com logo in svg

Chroma 19032-P, Быстрый старт

Поделиться
Скачать
Chroma 19032-P Скачать руководство пользователя страница 15

Electrical Safety Analyzer 19032-P Quick Start Guide

 

1 

1.    Introduction 

1.1 

An Overview of Product 

Automatic withstand / insulation / grounding testers of the instrument are 
designed for automatic withstand, insulation resistance, grounding 
resistance, short/open circuit detection and dynamic leakage current test of 
electromechanical and electronic equipments.     
 
The aspect of withstand voltage testing, the output power is AC: 500VA(5kV, 
100mA), DC: 150VA(6kV, 25mA).    Therefore, it is for withstand test of 
electronic and electromechanical and component.     
 
Testing aspect of insulation resistance, the measurement range is 0.1M

Ω

 

∼

 

50G

Ω

 and test voltage range is 50V 

∼

 1000V can be set arbitrary.     

 
Testing aspect of grounding resistance, the grounding resistance range can 
be measured is 10 

∼

 150m

Ω

, under 10A can up to 510m

Ω

.  The output 

test current range is 3 

∼

 40A can be set arbitrary.     

 
Testing aspect of dynamic leakage current, the measurement range is 
0.01mA 

∼

 50.0mA (rms).    The output test voltage range is 90V 

∼

 280VAC.   

The test rule matches to IEC950, UL544, UL2601 etc.   
 
In the testing aspect of short/open circuit detection, please test if 
capacitance is short or open before testing high voltage.    Please make 
sure the DUT good contact then processes high voltage test. 
 
All of setting status, time, current, voltage, resistance value, memory 
number etc are list on the display, it is unnecessary to remember any 
parameter status which be set.     
 
The tester equipped with Good and No Good judgment machinery and 
signal output of testing result and remote control.    It is also for GPIB 
interface, SCANNING interface, RS232 interface of automatic test system.   
The above equipments makes high efficient and accurate test. 
 
 

Содержание 19032-P
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды