Additional Support
Check our web site often for updated technical information produced in an effort to help you, our customers, stay on your bike. Visit: chrisking.com/support.
Additional Questions? Please email us at [email protected] or call the Customer Service Hotline at 800-523-6008.
Limited Warranty
Chris King Precision Components (“CKPC”) warrants this product to be free from defects in materials or workmanship for a period of ten (10) years from the original
date of purchase. If a defect is found and the product is within its warranty period, our entire liability and your sole remedy will be to, at our sole discretion and to the
extent permitted by law, either repair the product using new or refurbished parts, replace your product with a new or refurbished product functionally at least equivalent
to yours, or accept the return of the product in exchange for a refund of the purchase price you paid.
This limited warranty does not cover damage or failure resulting from misuse, abuse, alteration, neglect, normal and reasonable wear and tear, crash or impact, accidents,
failure to perform routine maintenance, improper installation, or use other than that for which the product was intended. This limited warranty does not cover any product
where the serial number has been altered or removed.
THE LIMITED WARRANTY WRITTEN ABOVE IS THE ONLY EXPRESS WARRANTY KING CYCLE PROVIDES FOR THE PRODUCT, AND THE ABOVE REMEDY IS YOUR
SOLE REMEDY. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, KING CYCLE EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS OF
ANY KIND, WHETHER STATUTORY OR IMPLIED, ARISING FROM COURSE OF CONDUCT OR OTHERWISE, REGARDING THE PRODUCT, EXCEPT THAT ANY IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, NON-INFRINGEMENT, AND OTHERWISE ARE LIMITED IN DURATION TO THE APPLICABLE
PERIOD OF THE EXPRESS WARRANTY ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
LIMITATION OF LIABILITY: YOU EXPRESSLY UNDERSTAND AND AGREE THAT, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, CKPC AND ITS SUBSIDIARIES
AND AFFILIATES SHALL NOT BE LIABLE TO YOU UNDER ANY THEORY OF LIABILITY (WHETHER CONTRACT, TORT (INCLUDING NEGLIGENCE), BREACH OR FAILURE
OF ANY WARRANTY OR OTHERWISE) FOR ANY INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL, PUNITIVE, OR EXEMPLARY DAMAGES THAT MAY BE INCURRED
BY YOU IN CONNECTION WITH THE PRODUCT OR THESE TERMS, WHETHER OR NOT SUCH PARTY OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF OR SHOULD
HAVE BEEN AWARE OF THE POSSIBILITY OF ANY SUCH LOSSES ARISING. YOU EXPRESSLY UNDERSTAND AND AGREE THAT, TO THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, THE TOTAL LIABILITY IN CONNECTION WITH THE PRODUCT OR THIS LIMITED WARRANTY WILL NOT EXCEED THE AMOUNT YOU ACTUALLY
PAID FOR THE PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Please see our website www.chrisking.com for specific warranty terms and how to make a warranty claim.
Thank you for your purchase!
Part#10999 Rev. 07/18
Made in the USA
All Chris King Precision Components products are manufactured in the USA using industry leading environmental and quality control standards.
Chris King Precision Components
2801 NW Nela Street, Portland, Oregon 97210
800.523.6008 | www.chrisking.com | [email protected]
DropSet
™
1
DropSet
™
ream depth
upper stack height
bearing seat angle
ream depth
bearing seat angle
Type
Bearing Position
S.H.I.S.
Bearing O.D.
Headtube I.D.
Fork Steerer Tube O.D. Crown Seat O.D. Bearing Seat Angle
Stack Height Ream Depth
Upper
IS41/28 45°
41.0mm
41.15mm (+0.05 -0.05) 28.60mm (+0.05 -0.05)
NA
45°
9mm
3.1-3.2mm
Lower
IS52/40 45°
52.0mm
52.10mm (+0.05 -0.05)
NA
39.79-39.85mm
45°
1mm
7.4-7.5mm
Headset Specifications
Dr
op
Se
t™ 1
Stem Cap Bolt Torque = 1.92Nm (17 in.lbs)