WiFi+GSM/4G
Smart Security Alarm System
User’s Manual
The version number: WT2BX-EN-V1.0-2020011
We reserve all the right of explanation of this user manual
Indicators:
Keys:
Wired Alarm Interface:
NC: Relay normal close, the alarm is disconnected;
COM: Relay common port;
NO: Relay normal open, alarm pull-in;
Z1: Wired zone 1;
Z2: Wired zone 1;
(The wired detector NO/NC can be selected for operation on the host panel).
3. Daily Use
3.1. Common Operations
3.2. Telephone Operation
Once the host alarms, the siren will immediately give off a prompt sound; at the
same time, it automatically dials the preset phone number for voice alarm. When
the alarm call is not answered, the host will automatically call the next group of
phone number, and dial all preset phone numbers three times in a loop. If the
dialed call is answered, the host turns off the siren, the phone receiver will receive
an alarm message and repeated zone code. At this time, pressing the telephone
keypad can realize different functions:
System arm host in on-hook status: the host dials all phone numbers three times in
a loop.
Press [1#] Key: System arm the host stops alarm, start arming; the host no longer
makes calls.
Press [2#] Key: System disarm the host stops alarm, start disarming; the host no
longer makes calls.
Press [3#] Key: Listen-in the host turns off the siren and monitors the scene for 60s
to monitor for abnormal sounds or thieves intrusion in the house.
Press [4#] Key: Interoom start on-site intercom function for 60s.
Note: When the system receives the wrong command, the system will play the
alarm message and turn off the intercom. If you need restart the intercom, please
re-enter [4#].
3.3. Remote Controller
Dial the host number remotely, enter the pa# according to the voice
prompt after connecting, then
The host in on-hook status: the host dials all phone numbers three times in a loop.
Press [1]: arm, if finished successfully, you will hear a voice prompt “System
armed”.
Press [2]: disarm, if finished successfully, you will hear a voice prompt “System
disarmed”.
Press [3]: monitoring for 30 seconds, to continue monitoring, press [3] again to
monitor for another 30 seconds.
Press [4]: two-way intercom for 30 seconds. You can’t operate the main unit during
this time.
4. Preparation Before Use
4.1. Installation of GSM/4G-SIM Card
①
Please install the SIM card when the host is off;
②
Connect the correct DC-5V power adapter, slide the power switch of the host to
ON side.
。
4.2. Quick Setting
4.2.1. Download mobile app
●Download “ Smart Life” in App Store or Google Play or scan the below QR code
to download the App.
●After the APP is installed, please follow the page prompts to register an account
and log in: Enter the App, click [Register], use your mobile phone number or email
to follow the App page to register an account.
4.2.2. Host Wi-Fi Networking
Fast Networking Mode
①
Make sure the phone is connected to the WiFi rounter (for dual-band router,
please select 2.4G connection);
②
Open the APP, click [+] in the upper right corner of the main page; select
[Security & Sensors]-> [Alarm (Wi-Fi)];
③
The host enters the WiFi fast networking mode: first, after the smart security
host is powered on, enter the administrator password, press the Enter key to
enter the system menu page, and then choose to enter [Setting]-> [WiFi setting]->
[Smarklink], The network indicator blinks fast and enters fast networking mode.
④
Click the Next button on the APP page, select the WiFi to be connected and
enter the WiFi password, and click Next to connect the WiFi; the network indicator
keeping steady-on indicates that the host is successfully connected to the Internet.
Note: The host is better installed near the wireless router; 5Ghz WiFi band is not
supported currently.
4.2.3. Hotspot Mode
If the default fast networking is unsuccessful, you can select "hotspot mode" for
networking.
①
Make sure the phone is connected to the WiFi rounter (for dual-band router,
please select 2.4G connection);
②
Open the APP, click [+] in the upper right corner of the main page; select
[Security & Sensors]-> [Alarm (Wi-Fi)],click Next and select "AP Mode" on the
upper right corner of the page;
③
The host enters the WiFi hotspot networking mode: first, after the smart security
host is powered on, enter the administrator password, press √ key to enter the
system menu page, and then choose to enter [Setting]-> [WiFi setting]-> [Softap],
The network indicator flashes slowly and enters the WiFi hotspot networking mode;
④
Click "Confirm indicator slowly blink" on APP page-> select the WiFi to be
connected and enter password-> confirm-> go to connect;
⑤
Find "SmartLife-xxxx" in the WiFi list of the mobile phone and click Connect.
After the connection is successful, return to the "SmartLife" APP to perform the
WiFi configuration process, the indicator keeps steady-on, indicating that the host
is successfully connected to the network.
5. APP Operation
5.1. Device Control
Home Arm:
This mode is applicable when someone is at home, the accessories in
ordinary defense zone being triggered can not trigger the alarm; the accessories in
other defense zones being triggered will trigger the alarm.
Away Arm:
This mode is applicable when no one is at home, any detection alarm
device will trigger the alarm.
Disarm:
In this mode, the system is disarm. The alarm is triggered only if the
accessories in the emergency zone are triggered.
Trigger Alarm:
APP control host alarm.
5.2. History Records
Display user operation records and alarm records.
5.3. Add Accessories
For the products purchased in a kit, accessories have been added, no need for this
step.
When you need to add accessories, please choose any of the following ways to
add:
Method 1 (APP): Open the APP, enter the host page, select [Accessories]->
[+] below, the host enters the code pairing state (the indicator light flashes red
quickly), at this time trigger the device to be added, such as Window/door sensor,
PIR Detector and Remote Controller; only one accessory can be added at a time.
After the addition is successful, the APP page will pop up a window to remind,
and the host will exit the code pairing state.
Note: APP can add wireless devices, RFID, and the NC / NO attributes of wired
devices need to be modified on the host.
Method 2 (see page 14: add directly from the alarm host): support to add up to 100
wireless detectors.
Note
：
1. After the accessories are added successfully, the host will beep once, and when
the device is added repeatedly, the host will beep twice;
2.The accessories in a kit have been added when leaving the factory; For other
wired accessories and RFID addition, please refer to the following [Device
management];
Trigger PIR: PIR detects human movement;
Trigger door magnet: separate the launch box and the magnetic strip box by more
than 0.39in/10mm;
Trigger remote control: Press the Away Arm, Home Arm or Disarm button on the
remote controller.
5.4. Accessory Attribute Editing
5.5. Setting
①
Set the Arm delay time, 0s, 30s, 60s and 90s are optional.
②
Set timed arm and disarm.
③
On: sound alarm when alarming;
Off: mute when alarming. Default: On.
④
Alarm time APP, 4 options available: 60s, 120s, 180s, 240s. Default: "180s".
⑤
On: APP or keyboard operation or setting, host prompt tone feedback;
Off: APP or keyboard or setting, no host prompt tone feedback. Default: On.
⑥
On: when the accessory is low battery, push notification;
Off: when the accessory is low battery, no push notification. Default: On.
⑦
On: receive alarm notification;
Off: do not receive alarm notification. Default: On.
⑧
0s, 30s, 60s and 90s are optional; Default: 30s.
⑨
On: the doorbell function is on;
Off: the doorbell function is off. Default: Off.
Note: Firstly you need to change the device type of the corresponding accessory to
doorbell, and then turn on the doorbell switch in the settings to make the doorbell
function effective.
⑩
Set alarm phone number, Max. 6 groups.
⑪
Set alarm SMS number, Max. 6 groups.
⑫
Control the host to restore the factory settings, clear the accessory data and WiFi
networking data.
⑬
Set the host language version, please set the corresponding language version
according to the region.
5.6. Timed Arm/Disarm Setting
Select [Setting]-> [timer] to add timer. Allow to set timer for Away arm, Home arm or
disarm, etc.
5.7. Doorbell Setting
①
Add the doorbell button or other accessories to the host, please refer to [Add
Accessories];
②
Find the added detector device in [Accessories] on the main page of the APP
device, change its device type to [Doorbell], rename and save it;
③
Turn on the doorbell switch in the settings;
④
At this time, when the doorbell button or other accessory device is triggered,
the smart alarm will sound the doorbell prompt tone and push the information of
someone's visit to the mobile phone APP.
Note:
1. When the standard doorbell button in the set is added to the alarm, the default
name displayed on the [Accessories] page is "Door Magnet XX", and the device
type is "Door Magnet" by default, you need to change the device type to [Doorbell]
and rename it.
2. The device type is door magnet, PIR detector and other accessories can be set
as doorbell trigger, remote controller and emergency button do not support setting
as doorbell trigger.
6. Host Setting
Default administrator (account: admin; password: 123123 (modifiable))
Enter the administrator password on [Standby Page], press √ to enter the [System
Menu]
6.1. Number Management
Add Number
Support to set 6 groups of alarm phone numbers and 6 groups of alarm SMS
numbers.
①
On the system menu page, press 1 or
【
↑/↓
】
key to select [Setting], press √ key
to enter [System setting];
②
Select [+ Add phone], press √ to enter [Add phone];
③
Enter the phone number, press the ↓ key to move the cursor to the phone or
SMS, and press the √ key to set the number as the alarm phone number or alarm
SMS number;
④
Press ↓ key, move the cursor to [Save and Back] and press √ key to save.
Edit Number
On the [Phone management] page, press ↑ or ↓ to select the number to be edited
and press √ key, select [Edit] and press √ key to modify the number or modify the
alarm mode of this number, move the cursor to [Save and Back] and press √ key
to save.
6.2. Device Management
Wireless Device Addition
Support to add up to 100 wireless detectors.
①
On the system menu page, press 2 or
【
↑/↓
】
key to select [Device], press √ key
to enter [Device management];
②
Select [Wireless device], press √ to enter [Wireless device];
③
Select [+ Add wireless device], press √;
④
Trigger the wireless detector to be added, move the cursor to [Save] and press
√ to save.
Wireless Device Attribute Setting:
On the [Wireless device] page, press ↑ or ↓ to select the device to be edited, press
√ key, select [Edit] and press √ key, set the device attributes and save.
Wired Device Management
Supports 2 wired inputs
①
On the system menu page, press 2 or
【
↑/↓
】
key to select [Device], press √ key
to enter [Device management];
②
Select [Wired device], press √ to enter the [Wired device] page;
③
Select the wired device to be edited, press √ key to enter the attribute setting.
Wired Device Attribute Setting
Input Detection: After turning on the feature, the wired port input is valid.
NC / NO: Select according to the (Off / On) trigger type when the accessory alarms.
Ordinary defense zone / Home defense zone / 24-hour defense zone / Delay
defense zone: Set the type of defense zone for wired devices.
6.3. RFID Card Management
RFID Addition
Support add up to 10 RFID.
①
On the system menu page, press 2 or
【
↑/↓
】
key to select [Device], press √ key
to enter [Device management];
②
Select [RFID card], press √ key to enter the [RFID card] page;
③
Select [+ Add RFID], press √ key;
④
Trigger the RFID card to be added, move the cursor to [Save] and press √ to
save.
RFID Attribute Setting
On the [RFID card] page, press ↑ or ↓ to select the device to be edited, press √ key,
select [Edit], press √ key, exit after set RFID attributes successfully.
RFID Card Attributes:
Card Swipe Sound: After turning on the RFID function, there will be voice prompts
when swiping RFID card.
Swipe to Arm: After turning on the RFID function, the system Armed operation can
be performed when swiping the RFID card.
Swipe Card to Disarm: After turning on the RFID function, the system Disarmed
operation can be performed when swiping the RFID card.
6.4. User Management
Support up to 16 user accounts (1 administrator account (admin), 15 guest
accounts (guest)).
Note: Only entering the correct administrator password can enter the [System
Menu].
User Addition
①
On the system menu page, press 3 or
【
↑/↓
】
key to select [User], press √ key to
enter [User management];
②
Select [+ Add users], press √ to enter the [Add users] page;
③
Enter the user password of the user, move the cursor to [Save and Back] and
press √ to save.
User Password Modification
On the [User management] page, press ↑ or ↓ to select the user account to be
edited, press √ key, select [Edit], press √ key, enter the new password, move the
cursor to [Save and Back] and press √ key to save.
User Delete
On the [User management] page, press ↑ or ↓ to select the user account to be
deleted and press √ key, select [Delete] and press √ key.
6.5. History Management
Operation Record
①
On the system menu page, press 4 or
【
↑/↓
】
key to select [History], press √ key
to enter [History];
②
Select [Operation record], press √ to enter the operation log review page.
Alarm Record
①
On the system menu page, press 4 or
【
↑/↓
】
key to select [History], press √ key
to enter [History];
②
Select [Alarm record] and press √ to enter the alarm record review page.
6.6. Voice Record
Voice Record Settings
①
On the system menu page, press 5 or
【
↑/↓
】
key to select [Record], press √ key
to enter [Voice record setting];
②
Select [Record], press √ key and count down 3 seconds to enter the record
(only a record of 10 seconds can be recorded, each re-record will cover the
previous record, after alarming, the record will play once when getting through
the phone call), once the record is 100% complete, the icon will change from
[Done] to [Record].
Play Record
On the voice record setting page, press 5 or
【
↑/↓
】
key to select [Play], and press
the √ key to automatically play the last recorded record;
Delete Recording
On the voice record setting page, press the ↑ or ↓ key to select [Delete], and press
the √ key to delete the record.
6.7. System Setting
6.7.1. WiFi Setting
Please refer to [Host Wi-Fi Networking] in [Quick Setting] for more details
,
page 07.
6.7.2. Doorbell
①
On the system menu page, press 6, or
【
↑/↓
】
key to select [Setting], press √ key
to enter [System setting];
②
Press ↑ or ↓ key to select [Doorbell], press √ key to enter [Doorbell] page; press
√ key to turn on or off the doorbell function;
③
Press ↑ or ↓ key to select [Trigger device], press √ key to enter the Trigger device
page; press ↑ or ↓ key to select the trigger device of the doorbell, and press the √
key to select or cancel.
6.7.3. Timer Setting
①
On the system menu page, press 6, or
【
↑/↓
】
key to select [Setting], press √ key
to enter [System setting];
②
Press ↑ or ↓ key to select [Timer setting], press √ key to enter the [Timer setting]
page;
③
Press ↑ or ↓ key to select [Timed disarm], [Timed arm] or [Timed home arm], and
press √ to enter the Add timed task page;
④
Press ↑ or ↓ key to select [+ Add timed task], press √ key, set the timing informa
-
tion and save according to the interface prompt.
6.7.4. Parameter Setting
①
On the system menu page, press 6, or
【
↑/↓
】
key to select [Setting], press √ key
to enter [System setting];
②
Press ↑ or ↓ key to select [Parameter setting], press √ key to enter the [Parame
-
ter setting] page;
③
Press ↑ or ↓ key to select the corresponding parameter, press √ key to enter the
setting.
6.7.5. Language Setting
①
On the system menu page, press 6, or
【
↑/↓
】
key to select [Setting], press √ key
to enter [System setting];
②
Select [Language setting], press √ to enter the [Language setting] page.
6.7.6. Operation Prompt Tone
On the [System setting] page, press 6, or
【
↑/↓
】
key to select [Operation sound],
and press √ to select ON or OFF;
ON: APP or keyboard for operation or setting, the host has prompt sound feedback;
OFF: APP or keyboard for operation or setting, the host has no prompt feedback.
Default: On.
6.7.7. Time Settings
①
On the system menu page, press 6, or
【
↑/↓
】
key to select [Setting], press √ key
to enter [System setting];
②
Select [System time setting], press √ to enter the [System time setting] page, and
press ↑ or ↓ to select and modify the time.
Note: When modifying the time, delete the existing number first and then enter the
new number.
6.7.8. GPRS Settings
①
On the system menu page, press 6, or
【
↑/↓
】
key to select [Setting], press √ key
to enter [System setting];
②
Select [GPRS server setting], press √ to enter the [GPRS server setting] page,
and press ↑ or ↓ to select and enter the ID, IP and other information to connect
(alarm monitoring center) platform.
6.7.9. Factory Settings
①
On the system menu page, press 6, or
【
↑/↓
】
key to select [Setting], press √ key
to enter [System setting];
②
Select [Factory default], press √ to enter the [Factory default] page, select
[Factory set] and press √.
6.7.10. System Version
①
On the system menu page, press 6, or
【
↑/↓
】
key to select [Setting], press √ key
to enter [System setting];
②
Select [System version], press √ to enter to query current model and software
version.
6.8. SMS Function
SMS Prompts
1. Message prompt of Host Armed, Disarmed and Home armed.
2. SMS message prompts of when plugging the external power source , unplugging
the external power source or low power.
3. SMS message prompts of low power in defense zone.
4. Alarm message prompt.
7. How to Install
Smart Security Alarm Host
When installing the host, please note that the distance between the host and the
wireless router should not be too far, just keep it at 6.56-16.4ft/2-5m.
The host should be installed in the central area of the defense area as much
as possible to ensure that the signals of all wireless detectors can be covered.
Please note that the host should be installed as far away as possible from large
metal objects or household appliances with high frequency interference, while
avoiding shields such as reinforced concrete wall protection and fire doors.
PIR Detector
1. Installed on the solid wall, about 5.9-6.56ft/1.8-2m above the ground
Use screws to fix the bracket on the wall; this installation method is suitable for
most solid walls.
2. Installation suggestion
Note: The detection range of this detector is fan-shaped (detection distance is
about 23ft/7m, detection angle is about 90°).
3. Warm notice
Window/Door Sensor
Use double-sided tape to attach the detector to the door or window.
When the battery needs to be replaced:
Please firstly use a screwdriver to separate the rear cover A, then replace the
battery.
8. Basic Specification
Smart Security Alarm Host
Power supply: DC 5V
Wireless standard: IEEE 802.11 b/g/n, 433.92MHz (transmit and receive)
RF distance: 229.7ft/70m (open air)
Modulation system: AM
Receive sensitivity
:
-110dBm
Static power consumption: ≤150mA
Alarm power consumption: ≤400mA
Working environment: temperature -10
℃
~ + 50
℃
, humidity
＜
90% RH
Product size: 200*136*31mm
PIR Detector
Battery model: DC 6V, 4 AAA batteries
Static current: ≤60uA
Alarm current: ≤20mA
Wireless standard: ASK433.92MHz
Wireless distance: ≥80m(open air)
Detection angle: 110° horizontal, 60° vertical
Smart Life
Working environment: +5
℃
~ + 45
℃
Product size: 116mm*60mm*38mm (without mounting bracket)
Window/Door Sensor:
Battery type: DC 3V, CR2032 lithium battery
Static current: ≤3uA
Alarm current: ≤20mA
Wireless standard: ASK433.92MHz
Wireless distance: ≥80m
Working environment: -20
℃
~ + 55
℃
Remote Controller:
Battery model: DC 3V, CR2032 lithium battery
Static current: ≤1uA
Alarm current: ≤10mA
Wireless standard: ASK433.92MHz
Wireless distance: ≥80m
Working environment: -20
℃
~ + 55
℃
9. Precautions
● Minimize the distance between accessories and the host;
● Please avoid reinforced concrete and electrical equipment between the acces
-
sories and the host;
● Please do not use the product in a humid environment;
● Please do not use the product in flammable and explosive environments;
● Please keep the product surface clean and dry.
10. Basic Configuration
Smart Security Alarm Host
1PC
PIR Detector
1PC
Windows/Door Sensor
2PCS
Remote Controller
1PC
Wired Siren
1PC
Power Adapter
1PC
User’s Manual
1PC
11. Simple Troubleshooting
12. Storage, transportation and after-sales service
Storage conditions:
Temperature(-10°C~+40*C), humidity
≦
90%, ventilated, no
corrosive objects, and the standard stacking layers < 6 layers.
Transportation conditions:
The stacked layers < 6 layers. Avoid impact during
transportation. The remaining conditions are as above.
After-sales service:
The company implements perfect after-sales service for
products. If the system fails, please do not disassemble and repair it by yourself.
Please contact the merchant you purchased.
STATUS
15:02
1
2020-05-29 星期五
2
0
5