background image

ODMLT

Installation Instructions

6

Concrete Installation

WARNING:

It is the responsibility of the installer to verify

that the structure to which the mount is anchored will safely
support five times the combined load of all attached
components and equipment.

1.

Determine a suitable mounting location and lift the wall plate
(A) into mounting position on wall.

2.

Using a small nail or screw (not provided) in the center hole,
lightly support the wall plate at the mounting location. (See
Figure 4)

3.

Level the wall plate (A) and drill 1/4" pilot holes for
anchoring the wall plate. Holes must be drilled between 16"
and 24" apart. (See Figure 4)

4.

Using four Buildex® Tapcon® anchors and four 5/16”
washers (X), install the wall plate (A) on the wall. (See
Figure 4)

Figure 4

5.

Slide the latches out on the wall mount in preparation for
installing display. (See Figure 5)

Figure 5

Interface Bracket Installation

1.

Place display face down on a soft, non-abrasive surface.

2.

Place left and right interface brackets (B and C) on the back
of the display, with the tension knob on each bracket facing
toward the outside of the television. (See Figure 6)

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display. Properly sized
screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer
screws of the same diameter.

NOTE:

Spacers (R and T) are used to offset the bracket if the

mounting holes are recessed or to get around the
protrusions.

3.

Secure the left and right interface bracket assemblies (B
and C) to the display. Select the mounting hardware that fits
your application. (See Figure 6)

Use spacers (R or T), if necessary.

Use M6 screws (H or J) or M8 screws (F or G) and 1/4"
washers (V).

Or, use M4 screws (N, P or Q) or M5 screws (K, L or
M), 1/4" washers (V) and #10 washers (U).

Figure 6

16” 

- 24”

concrete installation

3

1/4"

x 4

(X) x 4

(A)

Buildex®Tapcon®

4

anchors x 4

5

5

3

(F-Q) x 4

(V) x 4

(R or T) x 4
(if necessary)

(B)

(C)

(U) x 4

(w/M4 and M5
screws ONLY)

Содержание ODMLT









Отзывы: