CHIEF Goldwell CH1015T-LPGE / LPGEM Скачать руководство пользователя | Manualshive

Страница: 25 / 50

background image

C E N T R I F U G A L H E A T E R - C S A

Chief Industries, Inc. 800-359-7600 INSTALLATION - 416274

Page 25

Fan Electrical Installation

Connect the fan unit to the electric power source following the recommended wiring procedure
indicated in the fan manual. The electrical disconnect switch for the fan shall be sized with adequate

ampacity for the fan rating and installed in accordance with the Canadian Electrical Code Part 1 (CSA

Standard C22.1) and any local requirements.

Heater Electrical Installation

Note

: The heater is electrically interlocked with the fan electrical service.

The heater operates on 115 volt, single phase, 60 cycle power. For fans wired for 230 volt, verify that

the fan is wired with a neutral wire to the middle terminal of the fan terminal block (#2), as well as a

ground wire linked to the bottom terminal of the fan terminal block (#3) as shown. The heater power
cord is wired into the fan controls by connecting the black wire to the terminal (#1), the white wire to

terminal (#2), and the green wire to terminal (#3) of the fan terminal block, as shown. With the heater

wired into the fan circuitry, the fan must be operating before power is available to the heater.

«
...
23
24
25
26
27
...
»

Содержание Goldwell CH1015T-LPGE / LPGEM



















































Отзывы:

Нет отзывов

Похожие инструкции для Goldwell CH1015T-LPGE / LPGEM

Бренд: Waterstone Страницы: 6

Бренд: Olimpia splendid Страницы: 104

Бренд: A.O. Smith Страницы: 119

Бренд: Rheem Страницы: 48

Бренд: ICI Caldaie Страницы: 48

SBC 1100 ADV PLUS FR

Бренд: Quick Страницы: 76

Бренд: hajdu Страницы: 132

Бренд: Farelek Страницы: 14

Бренд: COLORATO Страницы: 7

Бренд: Sencor Страницы: 10

Бренд: EOS Страницы: 48

Бренд: Napoleon Страницы: 23

Бренд: Aquacal Страницы: 108

Бренд: BioSmart Страницы: 24

Thermo Pro 90 HDD

Бренд: Webasto Страницы: 6

Бренд: Procom Страницы: 64

Бренд: FELLER ENGINEERING Страницы: 11

Бренд: Anslut Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды