CHICAGO 93652 Скачать руководство пользователя страница 20

SKU 93652

For technical questions, please call 1-800-444-3353;

PAGE 20

Troubleshooting section at end of manual.

ELECTRICAL PARTS LIST & SCHEMATIC

Part # 

Code 

Model 

Description 

Qty. 

Remark 

1A X 

GF9-2P/ 

30335-0 

Single Phase 

2 Prong GFCI 

1  

2A 

L, N 

<UL> E199812 

SJTW  VW-1 

105°  16/C 

Power Cord 

With “UL”, “Water Resistant”, 

Mark: Black L, White N 

3A Q 

HF 

608 

Main 

Switch 

 

4A MOTOR 

KCL12-14 

BH-B  60Hz 

Universal Motor 

Lead Spec.: 105° 

16AWG x 2C 

5A K 

DMC-1220 

20.2A  125V AC 

10.1A 250V AC 

1/2HP 125-250V AC 

Mirco Switch 

Lead Spec.: UL SVT 

16AWG x 2 C  105° 

6A 

TMP 

CD70S 120A 

Thermostat 

Lead Spec.: 3321 18AWG 

150° 

 

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO
MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY
PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTI-
FIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK
AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACE-
MENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS

THERETO.

Содержание 93652
























Отзывы: