Chicago Pneumatic CPG 90-120 JD Скачать руководство пользователя страница 35

Страница: 35 / 56

- 35 -

Alternator troubleshooting

Symptom

Possible cause

Corrective action

Alternator gives 0 Volt

Blown fuse.

Replace fuse.

No residual voltage.

Excite the alternator by applying a 12V battery voltage with a 30 W
resistor in series on the + and - terminals of the electronic regulator,
respecting the polarities.

After being excited the alternator still
gives 0 Volt.

Connections are interrupted.

Check connection cables, measure winding resistances and compare
with values mentioned in the alternator manual.

Low voltage at no load

Voltage potentiometer out of setting.

Reset voltage.

Intervention of protection.

Check frequency/voltage regulator.

Winding failure.

Check windings.

High voltage at no load

Voltage potentiometer out of setting.

Reset voltage.

Failed regulator.

Substitute regulator.

Lower than rated voltage at load

Voltage potentiometer out of setting.

Reset voltage potentiometer.

Intervention by protection.

Current too high, power factor lower than 0.8; speed lower than 10%
of rated speed.

Failed regulator.

Substitute regulator.

Rotating bridge failure.

Check diodes, disconnect cables.

Higher than rated voltage at load

Voltage potentiometer out of setting.

Reset voltage potentiometer.

Failed regulator.

Substitute regulator.

Unstable voltage

Speed variation in engine.

Check regularity of rotation.

Regulator out of setting.

Regulate stability of regulator by acting on STABILITY
potentiometer.

Содержание CPG 90-120 JD

























































Результаты поиска

Содержание CPG 90-120 JD

Отзывы:

Бренды по названию

Популярные бренды

Chicago Pneumatic CPG 90-120 JD, Инструкция по эксплуатации

Результаты поиска

Содержание CPG 90-120 JD

Отзывы:

Бренды по названию

Популярные бренды