manualshive.com logo in svg

Chicago Pneumatic CPG 90-120 JD, Инструкция по эксплуатации

Поделиться
Скачать
Chicago Pneumatic CPG 90-120 JD Скачать руководство пользователя страница 32

- 32 -

Specifications GENCOOL EG 

GENCOOL EG is the only coolant that has been
tested and approved by all engine manufacturers
currently in use in Chicago Pneumatic compressors
and generators.

Chicago Pneumatic's GENCOOL EG extended life
coolant is the new range of organic coolants purpose
designed to meet the needs of modern engines.
GENCOOL EG can help prevent leaks caused by
corrosion. GENCOOL EG is also fully compatible
with all sealants and gasket types developed to join
different materials used within an engine.

GENCOOL EG is a ready to use Ethylene Glycol
based coolant, premixed in an optimum 50/50
dilution ratio, for antifreeze protection guaranteed to
-40°C (-40°F).

Because GENCOOL EG inhibits corrosion, deposit
formation is minimized. This effectively eliminates
the problem of restricted flow through the engine
coolant ducts and the radiator, minimizing the risk for
engine overheating and possible failure.

It reduces water pump seal wear and has excellent
stability when subjected to sustained high operating
temperatures.

GENCOOL EG is free of nitride and amines to
protect your health and the environment. Longer
service life reduces the amount of coolant produced
and needing disposal to minimise environmental
impact.

To ensure protection against corrosion, cavitation and
formation of deposits, the concentration of the
additives in the coolant must be kept between certain
limits, as stated by the manufacturer's guidelines.
Topping up the coolant with water only, changes the
concentration and is therefore not allowed.

Liquid-cooled engines are factory-filled with this
type of coolant mixture.

Coolant check

Monitoring coolant condition

In order to guarantee the lifetime and quality of the
product, thus to optimise engine protection, regular
coolant-condition-analysis is advisable.

The quality of the product can be determined by three
parameters.

Visual check

–

Verify the outlook of the coolant regarding colour
and make sure that no loose particles are floating
around.

pH measurement

–

Check the pH value of the coolant using a pH-
measuring device.

–

Typical value for EG = 8.6.

–

If the pH-level is below 7 or above 9.5, the coolant
should be replaced.

Glycol concentration measurement

–

To optimise the unique engine protection features
of the GENCOOL EG the concentration of the
Glycol in the water should be always above 33
vol.%.

–

Mixtures with more than 68 vol.% mix ratio in
water are not recommended, as this will lead to
high engine operating temperatures.

–

A refractometer can be ordered from Chicago
Pneumatic with part number 2913 0028 00.

Liter

US 

gal

Imp 

gal

cu.ft

Order 

number

can

5

1.3

1.1

0.175

1626 2255 00

can

5

1.3

1.1

0.175

1626 2257 00

can

20

5.3

4.4

0.7

1626 2256 00

Содержание CPG 90-120 JD

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды