manualshive.com logo in svg

Chicago Pneumatic CPG 90-120 JD, Инструкция по эксплуатации

Поделиться
Скачать
Chicago Pneumatic CPG 90-120 JD Скачать руководство пользователя страница 23

- 23 -

Triple voltage (3V)

The generator can run in three different modes:

–

1 phase

When using this selection, the generator provides
a 240/277 V output voltage.

–

3 phase, lower voltage

When using this selection, the generator provides
a 208/240 V output voltage.

–

3 phase, higher voltage

When using this selection, the generator provides
a 416/480 V output voltage.

Q1.1 ....Circuit breaker for low voltage, high 

current

Interrupts the low voltage power supply
towards X1 when a short-circuit occurs at
the load side or when the overcurrent
protection is activated. It must be reset
manually after eliminating the problem.

Q1.2 ....Circuit breaker for high voltage, low 

current

Interrupts the high voltage power supply
towards X1 when a short-circuit occurs at
the load side or when the overcurrent
protection is activated. It must be reset
manually after eliminating the problem.

R12 .....Output voltage adjust potentiometer

Allows to adjust the output voltage.

Depending on which mode the generator is running
in, circuit breaker Q1.1 or Q1.2 will be operational.

Circuit breakers Q1.1 and Q1.2 cannot be switched on
at the same time. This is prevented by means of the
auxiliary voltage selection relays S10b and S10c
(refer to the circuit diagram).

The selection between the three voltage modes is
performed by means of S10.

S10......Output voltage selection switch

Allows to select a 1 phase output voltage, a
3 phase high output voltage or a 3 phase low
output voltage. Selector switch S10 is
located on the alternator.

Changing the output voltage is only
allowed after shutdown.
After changing the output voltage by
means of the selection switch S10,
adjust the output voltage by means of
potentiometer R12 to the required
value.

Содержание CPG 90-120 JD

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды