background image

18. 

Always turn off the Circular Saw  and unplug it from its electrical outlet

 

before changing accessories or performing any inspection, maintenance, or 

 

cleaning procedures.

19. 

                   

The warnings and cautions discussed in this manual cannot cover all  

 

possible conditions and situations that may occur.  It must be under stood by the   

 

operator that common sense and caution are factors which cannot be built into 

 

this product, but must be supplied the the operator.

SKU 90186   

 

 

 

PAGE 7

Improperly connecting the grounding wire can result in the risk of electric

shock.  Check with a qualfified electrician if you are in doubt as to whether the 

outlet is properly grounded.  Do not modify the power cord plug provided with

the tool.  Never remove the grounding prong from the plug.  Do not use the

tool if the power cord or plug is damaged.  If damaged,  have it repaired by

a service facility before use.  If the plug will not fit the outlet, have a proper

outlet installed by a qualified electrician.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

1. 

Tools marked with “Grounding Required” have a three wire cord and three prong   

 

grounding plug.  The plug must be connected to a properly grounded outlet.  If    

 

the tool should electrically malfunction or break down, grounding provides a low    

 

resistance path to carry electricity aways from the user, reducing the risk of  

 

 

electric shock.  

(See Figure A, next page.)

20. 

                    

Some dust created by power sanding, sawing, grinding,  

 

 

 

drilling, and other construction activities contain chemicals known to the State of   

 

California to cause cancer, birth defects or other reproductive harm.  Some  

 

 

examples of these chemicals are: lead from lead-based paints, crystalline silica    

 

from bricks and cement and other masonry products, arsenic and chromium from  

 

chemically treated lumber.  Your risk from these exposures varies depending on    

 

how often you do this type of work.  To reduce your exposure to these chemicals    

 

work in a well ventilated area, and work with approved safety equipment such as   

 

those dust masks that are specially designed to filter out microscopic particles.  

   

 

(California Health & Safety Code 25249.5 et seq.)

  

21. 

                   

People with pacemakers should consult their physician(s) before us-

ing this product.  Operation of electrical equipment in close proximity to a heart 
pacemaker could cause interference or failure of the pacemaker.

WARnInG

WARnInG

WARnInG

WARnInG

Содержание 90186




















Отзывы: