Chicago Electric 67616 Скачать руководство пользователя

Страница: 1 / 16

Visit our website at: http://www.harborfreight.com

Email our technical support at: [email protected]

ITEM 67616

Read this material before using this product.

Failure to do so can result in serious injury.

SaVE thiS manual.

2012 by Harbor Freight Tools

No portion of this manual or any artwork contained herein may be reproduced in

any shape or form without the express written consent of Harbor Freight Tools.

Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein.

Tools required for assembly and service may not be included.

When unpacking, make sure that the product is intact

and undamaged. If any parts are missing or broken,

please call 1-800-444-3353 as soon as possible.

Save This Manual

Keep this manual for the safety warnings and precautions, assembly, operating,

inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual

near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and

the receipt in a safe and dry place for future reference.

Owner’s Manual & Safety Instructions

Содержание 67616

















Результаты поиска

Содержание 67616

Отзывы:

Похожие инструкции для 67616

Бренды по названию

Популярные бренды

Chicago Electric 67616, Инструкция по эксплуатации и правила безопасности

Результаты поиска

Содержание 67616

Отзывы:

Похожие инструкции для 67616

Бренды по названию

Популярные бренды