Chicago Dryer Edge MAXX Скачать руководство пользователя страница 75

Страница: 75 / 288

Edge MAXX

Preventive Maintenance

4-19

4.5 Annual PM

(2000 hours)

WARNING

Do not repair or correct any

of these conditions without

reading and understanding

the Repair chapter.

Only qualiﬁed personnel

should troubleshoot and

repair this unit.

Make sure the power is

turned OFF at the main

disconnect switch.

Follow lockout/tagout

procedures approved for

your site. Follow local

regulations. Failure to do so

could result in serious injury.

Check and Grease Transfer

Conveyor Gears

Required Tools

Phillips screwdriver, grease gun,

Shell Darina

EP2 Grease or

equivalent, clean lint-free cloth

Perform only when the unit is OFF

with power disconnected.

Turn power OFF at the main disconnect

switch.

Remove the guard which protects access

to the transfer conveyor gears (Figure

4-25).

Clean off old lubricant from the drive

gears (Figure 4-26).

Check the gears for wear. If a gear is ex-

cessively worn, replace it.

Grease the gears using the Shell Darina®

EP2 grease or equivalent.

Replace the protective panel removed in

Step 2.

Figure 4-26: Transfer conveyor gears located under

the side conveyor table.

Figure 4-25: A guard protects access to the transfer

conveyor gears.

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Chicago Dryer Edge MAXX, Инструкция по эксплуатации, Страница: 75 / 288

Результаты поиска

Содержание Edge MAXX

Отзывы: