Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 214 / 288

3024-024e

Edge Maxx

C-18

Spreader Section Tests

(SPR1)

The control system automatically begins to

operate parts of the upper and lower spreader

subsystems.

The panel display shows:

OUT/IN LSPREAD CTFLOOR
PS4/PS1 316/306 239/240

This display deals with the upper spreader

servo motor at low torque, moving the spreader

clamps in and out. It also activates the lower

spreader belts and the bottom ﬂoor motor (240).

The center ﬂoor motor (239) is no longer used.

(SPR2)

The control system automatically begins to

operate parts of the upper and lower spreader

subsystems.This tests the components of the

lower spread section.

The panel display shows:

SPRED CLAMP BLAST RET
PS3 216/224 233/234 PS1

This display deals with the upper spreader

servo motor at high torque, moving the spreader

clamps in and out. It also opens and closes the

spreader clamps, triggers the laydown air blast,

and causes the lower spreader belt gap rolls to

move in and out.

Sensor Activation Test (SENSOR)

Standard Testing

The panel display shows:

SENSOR ACTIVATION TEST

The control system automatically begins to

test each individual input device. As long as the

display does not change, no sensor problems

were detected.

Speciﬁc Sensor Testing

This test can also be used to test a speciﬁc

sensor by momentarily blocking it. In this case,

the display will brieﬂy display an error message

and indicate the LED number:

SENSOR FAILED/MISALIGNED

(105) ENTRY LEFT INLET

New Photosensor Setup

In addition, the Sensor Activation Test is used

to set up a replacement sensor to either dark or

light operate.

It can also be used to set sensor sensitivity but,

as a rule, this is always left at the default factory

maximum sensitivity setting.

All photosensors come set to DO (Dark

Operate) as the factory default. To determine

the proper setting for a new sensor, refer to the

OPERATING PRINCIPLES

chapter,

Electrical

System

section,

Control System

subsection to

determine whether the sensor should be DO or LO

(Light Operate). Note that only the Crossbeam

Sensors (PE45E/PE45R) are LO.

To set a new sensor, refer to the

REPAIR

chapter,

Sensors

section,

Photosensor

Replacement

procedure.

TOC

INDEX

C-TOC

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды