Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 210 / 288

3024-024e

Edge Maxx

C-14

Start Testing

To test any of the CHI Panel’s functions,

follow these ﬁrst steps:

Locate the appropriate schematic(s).

Turn power OFF at the main disconnect

switch.

Open the right endframe door and locate

the I/O modules. During the test, the LED’s

will light to show the control signals.

WARNING

This safety interlock switch

is only to be defeated

temporarily while performing

this procedure. Never

operate the unit unless

all safety systems

are working correctly.

Serious Injury Could Result.

The unit will not operate while a safety

interlock switch is open. As a temporary

measure during this procedure, defeat the

door interlock switch by inserting one

of the switch keys that shipped with the

unit.

Perform only when the unit is

RUNNING.

Use extreme caution.

Make sure the compressed air supply to

the unit is ON.

Turn power ON at the main disconnect

switch and start the unit.

Test mode can only be entered if the

spread/feed system is off. Make sure no

STATION button is lit and the CHI Panel

display reads:

FEEDER OFF

Press and hold the TEST button; then,

press the ENTER button. Release both

buttons. The SELECT TEST menu dis-

plays as follows:

SELECT TEST

IN12 TR12 SPR12 IRN SENSE

The flashing cursor is under the 1 of

IN12.

Press the CURSOR button until the ﬂash-

ing cursor is under the desired adjustment

area:

IN1 is used to test the left inlet station.

See

Inlet Section Tests

IN2 is used to test the right inlet station.

See

Inlet Section Test

TRN1 is used to test the left station

transfer system. See

Transfer Section

Tests

TRN2 is used to test the right station

transfer system. See

Transfer Section

Tests

SPR12 is used to test the upper and

lower spreader systems. See

Spreader

Section Tests

IRN has no associated tests and appears

for display purposes only.

SENSE is the sensor activation test and

it used to check general sensor func-

tion, speciﬁc function and to properly

setup replacement sensors. See

Sensor

Tests

•

TOC

INDEX

C-TOC

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды