Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 168 / 288

Repair

Edge MAXX

7-36

Figure 7-48: Slowly rotate the motor and roll the

belt off its pulley.

Figure 7-47: A side conveyor motor cover is located

at each end of the machine.

To apply the tape:

Cut a 3-1/8” to 3-3/16” (80 mm) strip

for each placement.

Remove the backing from the tape

Line the tape up with the center

mark.

Wrap the tape around the roll and butt

the ends together

Repeat Step 7 for each tracking tape loca-

tion.

Bring the ribbons back into position and

replace the connecting pins.

Side Conveyor Drive Belt Tension

Adjustment

Over time, a side conveyor’s power twist

drive belt will stretch due to normal wear and

tear. Tension on the belt must be adjusted if it is

noticeably slack or if it begins to slip.

Required Tools

Phillips screwdriver, pliers

Perform only when the unit is OFF

with power disconnected.

Turn power OFF at the main disconnect

switch.

Locate the motor cover for the side con-

veyor drive belt which needs adjustment

(Figure 7-47).

Remove the screws which secure the cover

and move it out of the way.

Remove the side conveyor drive belt by

slowly hand-turning the motor drive pul-

ley (Figure 7-48) and rolling the belt off.

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды