Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 153 / 288

Edge MAXX

Repair

7-21

Slide the linear bearing assembly block

back onto the appropriate spreader rail and

secure the end of the rail with the screw

removed in Step 4.

Reconnect the e-chain and spread clamp/

air cylinder by reversing Steps 2 and 3.

Lubricate the upper spreader rail. For more

information, refer to the

PREVENTIVE

MAINTENANCE

chapter,

Daily PM

section,

Lubricate Upper Spreader Rail

procedure.

11.

12.

13.

Lower Spreader Drive Belt Tension

Adjustment

Over time, the lower spreader drive belts will

stretch due to normal wear. Adjust tension on a

belt when it appears loose or begins to skip on the

timed pulleys. Both conditions cause excessive

wear on the belt and shorten its life.

Required Tools

9/16” wrench

Perform only when the unit is OFF

with power disconnected.

Turn power OFF at the main disconnect

switch.

As appropriate, open the right or left

endframe door to access the belt to be

adjusted.

Tension on the belt is adjusted by moving

the spreader belt drive motor (Figure 7-28,

A) in its slotted mounting holes:

Loosen the nuts securing the motor

bolts.

Move the motor to increase tension on

the belt (Figure 7-28, B).

When tension on the belt is adequate,

tighten the nuts.

Close and secure the endframe door.

Start the unit and feed several items to

verify the adjustment is correct.

Readjust as necessary.

Figure 7-28: The bolts holding the lower spreader

motor in position are in slotted holes.

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды