Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 136 / 288

Repair

Edge MAXX

7-4

Figure 7-2: The inlet conveyor lift bracket is

located at the front center of the unit.

Figure 7-1: The lower inlet conveyor belt should

touch the guide bar (A) and have a

small deﬂection just below it (B).

Inlet Conveyor Lift Cylinder Bracket

Adjustment

The upper and lower conveyor belts must have

enough pressure between them to enable the inlet

conveyor to effectively grasp and transport the

ﬂatwork.

The upper conveyor should make a slight

indent in the lower conveyor belt when properly

adjusted (Figure 7-1). However, proper pressure

can only be determined by the effective grasp

and transport of the ﬂatwork during operation of

the inlet conveyor.

Required Tools

7/16” wrench

Perform only when the unit is OFF

with power disconnected.

Turn power OFF at the main disconnect

switch.

Loosen the nut (Figure 7-2, A) which

secures the inlet conveyor lift air cylinder

to its bracket (B).

Raise or lower the bracket to create the

proper pressure between the two inlet

belts.

Tighten the nut which secures the inlet

conveyor lift air cylinder to its bracket.

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды