Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 129 / 288

Edge MAXX

Troubleshooting

6-27

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

6.11 CHI Panel

ISSUE

CAUSE

SOLUTION

CHI Panel is Not Functioning

No error message

1. 2-wire power cable from

P01 for power to the CHI

Panel is not connected.

Reconnect; replace if necessary.

•

CHI Panel is Not Functioning

Message reads:

COMMUNICATION ERROR/

FAULTY CODE RETURNED

1. Serial communications

cable from the CHI Panel

to Wago I/O control mod-

ule is loose.

Check and repair connection at both

ends.

•

2. Communication cable is

attached backward.

Turn the connector over.

•

3. Power supply/AC detect

board P01 is not suppling

power to the CHI Panel.

Check. Replace defective board as

necessary.

•

4. Wago I/O control module

is bad.

Replace.

•

CHI Panel is Not Functioning

Message reads:

COMMUNICATION ERROR/

NO RESPONSE FROM CON-

TROL

1. Serial communications

cable from the CHI Panel

to Wago I/O control mod-

ule is loose.

Check and repair connection at both

ends.

•

2. Communication cable has

broken wire.

Repair or replace.

•

3. Wago I/O control module

is bad.

Replace.

•

CHI Panel Doesn’t Change

Programs

1. Ironer is not started.

Start.

•

2. Folder not started.

Start folder unit.

•

3. CHI Panel is faulty.

Check and replace.

•

4. MPC2 Machine Controller

circuit board is bad.

Replace.

•

Parameter Error Message

Message reads:

MEMORY ERROR/

PARAMETERS WILL DEFAULT

1. CHI Panel component is

missing or bad.

CHI Panel contains a static memory

with the laundry’s speciﬁc program-

ming selections. Contact an authorized

service outlet for instructions.

•

Parameter Error Message

Message reads:

MEMORY INITIALIZED/

ADJUST ALL PARAMETERS

1. After replacement, the CHI

Panel chip only recognizes

factory defaults.

All programs need to be reset. Refer

to the

CHI PANEL OPERATION

bul-

letin,

Programming

and

Adjustment

sections.

•

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды