Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 119 / 288

Edge MAXX

Troubleshooting

6-17

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

ISSUE

POSSIBLE CAUSE

SOLUTION

(continued from previous page)

Corner Dropped During Trans-

fer

6. Transfer clamps are not

closing properly.

Adjust. Refer to the

REPAIR

chapter,

Transfer Section

section,

Transfer

Clamp Check and Adjustment

pro-

cedure.

•

7. Check the cylinder stroke

on the transfer clamp jaw

closes quickly and com-

pletely.

Check the cylinder stroke is properly

tensioned and adjusted. Refer to the

REPAIR

chapter,

Compressed Air

System

section,

General Air Cylinder

Adjustment

procedure.

•

8. The urethane material on

the clamps is worn.

Replace as necessary.

•

Corner Grabbed then Dropped

by the Transfer Clamp

1. The transfer clamps are

not closing properly.

Adjust. Refer to the

REPAIR

chapter,

Transfer Section

section,

Transfer

Clamp Check and Adjustment

pro-

cedure.

•

2. Check the wear on the

jaws of the transfer clamp.

Readjust the jaw at the cylinder or

replace it as necessary. Refer to the

REPAIR

chapter,

Compressed

Air System

section,

General Air Cyl-

inder Adjustment

procedure.

•

Transfer Carriage is Not

Reaching the Center Position

1. Debris on rail.

Clean. Lubricate as necessary. Refer

to the

PREVENTIVE MAINTENANCE

chapter,

Weekly PM

section,

Lubri-

cate Transfer and Upper Spreader

Rails

procedure.

•

2. Position sensor not prop-

erly gapped.

Adjust gap to .04” (1 mm).

•

Side Conveyor is Not Working

(continued on next page)

1. MTR8 (left) or MTR9

(right) malfunction

Check. Repair/replace as necessary.

•

2. MP8 is tripped.

Check/Reset. If motor protector con-

tinues to trip, check for short or other

problem in motor circuit.

•

3. CR31 (left) or CR32 (right)

has failed.

Check. Replace as necessary.

•

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды