Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 115 / 288

Edge MAXX

Troubleshooting

6-13

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

ISSUE

CAUSE

SOLUTION

Noisy Operation

1. Mechanical components

need lubrication.

Lubricate. Refer to the

PREVENTIVE

MAINTENANCE

chapter,

Semi-An-

nual PM

section,

Grease Bearings

procedure.

•

2. Inverter frequency setting

is causing noisy motor

operation.

Adjust frequency. For more informa-

tion, contact the factory service depart-

ment.

•

Ribbon Set Not Working

1. Improper tension on rib-

bons.

Adjust. Refer to the

REPAIR

chap-

ter, and the appropriate section and

procedure.

•

2. Ribbon drive roll tracking

tape worn smooth.

Adjust. Refer to the

REPAIR

chap-

ter, and the appropriate section and

procedure.

•

3. Inverter or motor protector

fault.

Refer to

Electrical

section problems,

Circuit Breaker/Motor/nverter Fault

•

Rotating Elements Stop

1. Drive belt or chain is slip-

ping or broken.

Adjust tension or replace if broken,

worn, or frayed.

•

2. Idler pulley loose or fro-

zen.

Adjust tension or replace.

•

3. If one rotating element

is stationary, check for a

broken shaft, bad bearing

or a loose or worn drive

sprocket.

Replace as necessary.

•

4. Check CHI Panel for message and locate appropriate solution within

this chapter.

Machine Operation is Sluggish

Message reads:

AIR PRESSURE IS LO

1. Incoming air pressure is

below 60 psi (415 kPa).

Make sure air supply to feeder is ON

and supply hose is not obstructed or

loose.

Make sure air supply to feeder is at

least 80 psi (550 kPa).

Make sure air ﬁlter is clean. Refer to

the

PREVENTIVE MAINTENANCE

chapter,

Semi-Annual PM

section,

Clean Air Filter/Regulator/Auto

Drain

procedure.

•

6.4 Mechanical

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды