Chevrolet 10 Series 1967, Руководство по обслуживанию, Страница: 322 / 605

ENGINE COOLING 6K-2
are indicative of exhaust gases leaking into the cool­
ing system.
Periodic Maintenance
Periodic service must be performed to the engine cool­
ing system to keep it in efficient operating condition.
These services should include a complete cleaning and
reverse flushing as well as a reconditioning service.
In the course of engine operation, rust and scale ac­
cumulate in the radiator and engine water jacket. The
accumulation of these deposits can be kept to a minimum
by the use of a good rust inhibitor but it should be
remembered that an inhibitor will not remove rust al­
ready present in the cooling system.
Two common causes of corrosion are: (1) air suction--
Air may be drawn into the system due to low liquid level
in the radiator, leaky water pump or loose hose con­
nections; (
2
) exhaust gas leakage—Exhaust gas may be
blown into the cooling system past the cylinder head
gasket or through cracks in the cylinder head and block.
Cleaning
A good cleaning solution should be used to loosen the
rust and scale before reverse flushing the cooling
system. There are a number of cleaning solutions avail­
able and the manufacturer's instructions with the particu­
lar cleaner being used should always be followed.
An excellent preparation to use for this purpose is GM
Cooling System Cleaner. The following directions for
cleaning the system applies only when this type cleaner
is used.
1. Drain the cooling system including the cylinder block
and then close both drain plugs.
2. Remove thermostat and replace thermostat housing.
3. Add the liquid portion (No. 1) of the cooling system
cleaner.
4. F ill the cooling system with water to a level of about
3 inches below the top of the overflow pipe.
5. Cover the radiator and run the engine at moderate
speed until engine coolant temperature reaches 180
degrees.
6
. Remove cover from radiator and continue to run the
engine for 20 minutes. Avoid boiling.
7. While the engine is still running, add the powder
portion (No. 2) of the cooling system cleaner and
continue to run the engine for
1 0
minutes.
8
. At the end of this time, stop the engine, wait a few
minutes and then open the drain cocks or remove
pipe plugs. Also remove lower hose connection.
CAUTION:
Be careful not to scald your hands.
NOTE:
Dirt and bugs may be cleaned out of
the radiator air passages by blowing out with air
pressure from the back of the core.
Reverse Flushing
Reverse flushing should always be accomplished after
the system is thoroughly cleaned as outlined above.
Flushing is accomplished through the system in a direc­
tion opposite to the normal flow. This action causes the
water to get behind the corrosion deposits and force
them out.
Radiator
1. Remove the upper and lower radiator hoses and re ­
place the radiator cap.
2. Attach a lead-away hose at the top of the radiator.
3. Attach a new piece of hose to the radiator outlet
connection and insert the flushing gun in this hose.
4. Connect the water hose of the flushing gun to a water
outlet and the air hose to an air line.
5.
Turn on the water and when the radiator is full, turn
on the air in short blasts, allowing the radiator to
fill between blasts of air.
CAUTION: Apply air gradually as a clogged
radiator will stand only a limited pressure.
6
. Continue this flushing until the water from the lead-
away hose runs clear.
Cylinder Block and Cylinder Head
1. With the thermostat removed, attach a lead-away
hose to the water pump inlet and a length of new hose
to the water outlet connection at the top of the engine.
NOTE: Disconnect the heater hose when re ­
verse flushing engine.
2.
Insert the flushing gun in the new hose.
3. Turn on the water and when the engine water jacket
is full, turn on the air in short blasts.
4. Continue this flushing until the water from the lead-
away hose runs clear.
Hot Water Heater
1. Remove water outlet hose from heater core pipe.
2.
Remove inlet hose from engine connection.
3. Insert flushing gun and flush heater core. Care must
be taken when applying air pressure to prevent
damage to the core.
Fan Belt
Adjustment
1. Loosen bolts at Delcotron slotted bracket.
2.
Pull Delcotron away from engine until desired ten­
sion reading is obtained with a strand tension gauge.
Refer to Section
6
, "Engine Tune Up” .
3. Tighten all Delcotron bolts securely.
Thermostat
The thermostat consists of a restriction valve actuated
by a thermostatic element. This is mounted in the hous­
ing at the cylinder head water outlet above the water
pump. Thermostats are designed to open and close at
predetermined temperatures and if not operating properly
should be removed and tested as follows.
Replacement
1. Remove radiator to water outlet hose.
2.
Remove thermostat housing bolts and remove water
outlet and gasket from thermostat housing (fig.
2
).
3. Inspect thermostat valve to make sure it is in good
condition.
4. Place thermostat in hot water
2 5 °
above the temper­
ature stamped on the thermostat valve.
5.
Submerge the valve completely and agitate the water
thoroughly. Under this condition the valve should
open fully.
6
. Remove the thermostat and place in water 10° below
temperature indicated on the valve.
7. With valve completely submerged and water agitated
thoroughly, the valve should close completely.
8
. If thermostat checks satisfactorily, re-install, using
a new housing gasket.
9. Refill cooling system.
CHEVROLET TRUCK SERVICE MANUAL