CHERUBINI CLIMA PLUS RX Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 44

CHERUBINI CLIMA PLUS RX Скачать руководство пользователя страница 37

76

After having memorised the limit switches, drive the rolling shutter to the opening
position and then perform the following command sequence:

At the end of the sequence, wait until the rolling shutter is completely lowered. From this
moment onwards the motor moves in “Dead Man” mode.

Carry out the following operations:

• Lower the rolling shutter until the adjustable slats are completely opened:

• Perform the following confirmation sequence:

The rolling shutter will move in sequence to the

memorised positions: closed, maximum opening.

Functions of the button panel*

Type of Command

Outside of tilting area

In tilting area

Up short

Completely raised

Closure of the slats and

fully raised

Down short

Completely lowered

Up long

Opening of the slats

Closure of the slats and

fully raised

Down long

Opening of the slats

Closure of the slats and

fully lowered

sequence DOWN/UP

(0.5 sec)

Opening of the slats

-

sequence UP/DOWN

(0.5 sec)

Opening of the slats

-

* see key to symbols and operational notes

SLAT OPENING MECHANISM SETTING

MODE 3

:

Orientable roller shutter with slats opening below the lower

limit without adjustable tilting function.

Only for roller shutter type / Rollflap / Biroll / Gelosia / Girasole / Easyroll / Inklina /Estella /
Luxor Noon, where the customer doesn’t need to adjust the number of open slats.
Not suitable for centralised control units. Not available on motors Ø 35.

PROGR.

FROM THE WHITE WIRE

E N G L I S H

«
...
35
36
37
38
39
...
»

Содержание CLIMA PLUS RX













































Отзывы:

Нет отзывов