CHERUBINI CLIMA PLUS RX Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 44

CHERUBINI CLIMA PLUS RX Скачать руководство пользователя страница 19

58

SLAT TILTING OR SLAT OPENING MECHANISM SETTING

OPERATIONAL NOTES

- What is meant by “short command” on the remote control is to press and hold the

button (A, B, C) for less than 2 sec. What is meant by “long command” on the remote
control is press and hold the button (A, B, C) for more than 2 sec.

- During the slat tilting movement, the adjustment of the opening of the slats is limited to

the minimum and the maximum of their opening.

- To enter into the slat tilting mode press the B button on the remote control with a

long command (2 sec). To use the tilting / orientation function and the middle position
function contemporaneously see the note on page 65.

- When one wishes to execute a long command, the motor also executes a short

command.

- To stop the rolling shutter during movement, press the stop button on the remote

control.

SPECIAL FUNCTIONS

SHORT-TERM SETTING OF A REMOTE CONTROL

This function makes it possible to store a remote control temporarily, for example, with
the purpose of setting the limit switches during assembly in the factory. A later final
saving of the remote control will be possible using the appropriate command sequence
(see: “SETTING THE FIRST REMOTE CONTROL”). The operations described below can be
carried out only when the motor has just come out of the factory or after a full memory
clearing (see: “FULL MEMORY CLEARING”). The motor makes the following operations
possible only within the time limits described in order to make sure that the short-term
setting is used only in the installation or factory setting phase and not during daily use.
Power up the motor, make sure that no other motors having an empty memory are
powered up in the same operating range.

Within 30 seconds after start,

press the B and C buttons simultaneously until the

motor gives a confirmation signal.

The remote control will remain stored for 5 minutes,

while the motor is powered up.

After 5 minutes or when the motor has its power cut off, the remote control will be
cancelled.
T1: First remote control to be stored

REMO

TE CONTROL PROGR.

E N G L I S H

T1

+

B

C

+

B

C

«
...
17
18
19
20
21
...
»

Содержание CLIMA PLUS RX













































Отзывы:

Нет отзывов