CHERUBINI A510078 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 22

CHERUBINI A510078 Скачать руководство пользователя страница 14

14

FIRMWARE UPDATE

RESET TO THE FACTORY SETTINGS

The system supports over-the-air firmware updates that do not require the device to
be removed from its location. The firmware update can be activated from all certified
controllers supporting version 2 of the Firmware Update function.

The device can be reset to the original factory with 6 consecutive clicks on the integrated
button.
After the reset is completed, the device will reboot and a RED solid led is showed.
Please use this procedure only when the network primary controller is missing or
otherwise inoperable.

INFO:

If the reset is performed while the device is still part of a network, it

notifies the other devices that it has been removed

(Device Reset Locally

Notification).

WARNING:

The system will be rebooted at the end of the firmware update

procedure. It is advisable to carry out the firmware update procedure only when
necessary and following careful planning of the intervention.

E

NG

L

IS

H

«
...
12
13
14
15
16
...
»

Содержание A510078























Отзывы:

Нет отзывов