Cherry Aerospace G84 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 12

Cherry Aerospace G84 Скачать руководство пользователя страница 4

TM-G84

Rev.: H DCR# 15-0406

DATE: 5/5/15

Federal Identification Code: 11815

© 2015 Cherry Aerospace

Tools without an integral Air Pressure Regulator (P-1505),

MUST be connected to a dedicated, regulated airline.

PUTTING THE TOOL IN SERVICE

The tool must be used with an air pressure regulator. Even if your shop air pressure is below the maximum recommended
range, pressure spikes in your airlines could cause serious damage to the tool or cause safety concerns.

HOW TO USE THE G84

LOCKBOLT INSTALLATION

After selecting the proper pulling head and attaching it securely to the G84, connect the air line to the tool.

Lockbolts:

Place the lockbolt pin into the workpiece and place the collar over the pintail.

While holding the back end of the lockbolt in place, push the pulling head onto the serrated area of the stem.

•

Caution:

When using a non-self-releasing pulling head once the tool is placed onto the serrated end, it cannot be removed unless

going through the installation cycle which breaks the serrated end of the bolt.
The broken part (pintail) will eject through the rear of the riveter when using a straight pulling head and through the rear of the active
area of the tool for when using offset pulling heads.

If the tool does not release the swaged collar after installation, it can be adjusted by adding shims behind the pulling head collet. If
the tool still does not release, see troubleshooting instructions on page:
See pulling head installation instructions.

BLIND BOLTS AND RIVETS

•

Insert the blind fastener into the prepared hole and place the tool onto the serrated stem.

•

Pull the trigger to activate the tool. Upon release of the trigger, the stem will eject to the rear of the riveter when using straight pulling

heads, and from the rear of the active area of the tool when using offset pulling head. Right angle pulling heads eject the stems
through the front..

PULLING HEADS

Pulling heads are not furnished and must be ordered separately. All Huck nose assemblies suitable for the 352 and 230 style tools will fit
directly on this tool.

Tools with an integral Air

Pressure Regulator (P-1505),

may be attached to any shop airline.

4

«
...
2
3
4
5
6
...
»

Содержание G84













Отзывы:

Нет отзывов