ChemInstruments PT-1000 Скачать руководство пользователя страница 3

Страница: 3 / 17

PRODUCT DESCRIPTION

Congratulations on the purchase of your new ChemInstruments Probe Tack Tester.
This versatile, user-friendly, carefully designed instrument allows you to determine
probe tack values of adhesive laminates.

WARNING: This equipment can cause injury if not used properly. It is
the operator’s responsibility to observe all safety rules and warnings.

The unit has the following features:

•

Automated test sequence.

•

Stores up to 20 tests in memory.

•

Stored test data is available for review.

•

Collected test data can be exported via RS232 port.

•

Selectable units of measure: Kilograms, Grams, Newtons, Pounds, and Ounces.

•

Compatible with EZ-Lab System software. See

www.cheminstruments.com

for

details.

SPECIFICATIONS

Electrical

Model specific

120V model: 120 VAC, 60 Hz, 2 amps

240V model: 240 VAC, 50 Hz, 2 amps

Operating Temperature

32 – 150 degrees Fahrenheit (0 – 70 degrees Celsius)

Humidity

0 – 55% relative humidity

Speed

Fixed speed of 24 inches per minute

Probe Diameter

5 millimeter

Physical Dimensions

Width: 12 inches (30 centimeters)

Depth: 15 inches (38 centimeters)

Height: 16 inches (40 centimeters)

Weight: 37 pounds (17 kilograms)

3 |

P a g e

Probe Tack Tester Operating Instructions (PT-1000)

Содержание PT-1000


















Результаты поиска

Содержание PT-1000

Отзывы:

Похожие инструкции для PT-1000

Бренды по названию

Популярные бренды

ChemInstruments PT-1000, Руководство по эксплуатации

Результаты поиска

Содержание PT-1000

Отзывы:

Похожие инструкции для PT-1000

Бренды по названию

Популярные бренды