manualshive.com logo in svg

Checkline humimeter RH5, Руководство по эксплуатации, Страница: 44 / 48

Поделиться
Скачать
Checkline humimeter RH5 Скачать руководство пользователя страница 44

humimeter RH5 & RH5.1 Operating Manual

Page 44

13.  Faults

If the measures listed below fail to remedy any faults or if the device has faults not 
listed here, please contact Schaller GmbH.

Fault

Cause

Remedy

Measuring error

The temperature of the ma-
terial being measured is too 
low or high. I.e. the material’s 
temperature is lower than  
-10 °C or higher than +60 °C

The temperature of the 
material being measured 
has to be between -10 °C 
and +60 °C.

Measurement error due to too 
short temperature adjustment 
time

Let the temperature adjust 
to the material being meas-
ured (see 

"5.2 Adjustment 

behaviour of the sensor"

).

Wrong product type

Check whether you have 
selected the right product 
type (product) before taking 
a reading (see 

"7. Product 

types"

).

Dripping water or sprayed 
water

Direct contact of the sensor 
with dripping or sprayed 
water will destroy it. 

Irreversible damage of the sen-
sor due to aggressive gases 

Please contact your dealer.

Condensation caused by a 
change in temperature

Condensation on the sensor 
interferes with the calibra-
tion. Let the device adjust 
to the surrounding tempe-
rature.

Polluted air humidity and tem-
perature sensor

Please contact your dealer.

Foreign particles on the sensor

Please contact your dealer.

Data transfer to Log-
Memorizer failed

Interface has not been config-
ured

The interface only has to 
be configured once. To do 
so, press the F1 key on your 
computer and read the Help 
file for your LogMemorizer 
program.

Содержание humimeter RH5

















































Отзывы:

Нет отзывов