manualshive.com logo in svg

Check Point Smart-1 150, Руководство по началу работы, Страница: 44 / 45

Поделиться
Скачать
Check Point Smart-1 150 Скачать руководство пользователя страница 44

Configuring LOM Settings 

 

Lights Out Management

     Page 44 

 

 

Relative (for Linux) 

3.  Click 

Apply Changes

. 

 

Configuring LOM Settings 

The network settings option enables you to change the default IP address and other basic network settings 
of the LOM card. 

To configure LOM network settings: 

1.  Click the 

LOM Settings 

menu option and select 

Network

. 

2.  Select 

Static 

and enter the following values. 

 

IP address

: the IP address of the LOM. 

 

Subnet mask

: the subnet mask of the LOM’s local network. 

 

Gateway IP address

: the Default Gateway IP address. 

 

Remote Console and HTTPS port

: port number on which the device’s Remote Console server and 

HTTPS server are listening. 

 

Setting the Date and Time 

This option enables you to manually change the date and time of the LOM card. 

 

Defining a LOM Login Message 

This option enables you to define the login message that appears when accessing LOM via a browser. 

To edit a login message: 

1.  Click the 

Device Settings

 menu option and select 

Login Message

. 

2.  Enter the login message text. 

3.  Click 

Apply Changes

. 

 

Содержание Smart-1 150














































Отзывы:

Нет отзывов