background image

4

Safety

Product Manual - CryoDoser FleX

 LN

2

 Dosing System

Caution!  Before removing parts or 

loosening fittings, empty the 

CryoDoser FleX system of liquid 

and release any vapor pressure 

in a safe manner.

Safety Bulletin

Portions of the following information are extracted from 

Safety Bulletin SB-2 from the Compressed Gas Association, 

Inc  at 

www cganet com

. Additional information on oxygen, 

nitrogen, and cryogenics is available in CGA Pamphlet 

P-9. Write to the Compressed Gas Association, Inc., 1235 

Jefferson Davis Highway, Arlington, VA 22202..

Oxygen Deficient Atmospheres

Warning!  Nitrogen vapors in air may dilute 

the concentration of oxygen 

necessary to support or sustain 

life.

The normal oxygen content of air is approximately 21%. 

Depletion of oxygen content in air, either by combustion 

or by displacement with inert gas, is a potential hazard and 

users should exercise suitable precautions.

One aspect of this possible hazard is the response of humans 

when exposed to an atmosphere containing only 8 to 12% 

oxygen. In this environment, unconsciousness can be 

immediate with virtually no warning.

When the oxygen content of air is reduced to approximately 

15 to 16%, the flame of ordinary combustible materials, 

including those commonly used as fuel for heat or light, 

may be extinguished. Somewhat below this concentration, 

an individual breathing the air is mentally incapable of 

diagnosing the situation because the onset of symptoms 

such as sleepiness, fatigue, lassitude, loss of coordination, 

errors in judgment and confusion can be masked by a state of 

“euphoria,” leaving the victim with a false sense of security 

and well being 

Human exposure to atmosphere containing 12% or less 

oxygen leads to rapid unconsciousness. Unconsciousness can 

occur so rapidly that the user is rendered essentially helpless.  

This can occur if the condition is reached by an immediate 

change of environment, or through the gradual depletion of 

oxygen 

Most individuals working in or around oxygen deficient 

atmospheres rely on the “buddy system” for protection. 

Obviously the “buddy” is equally susceptible to asphyxiation 

if he or she enters the area to assist the unconscious partner 

unless equipped with a portable air supply. Best protection 

is obtainable by equipping all individuals with a portable 

supply of respirable air. Life lines are acceptable only if the 

area is essentially free of obstructions and individuals can 

assist one another without constraint.

If an oxygen deficient atmosphere is suspected or known to 

exist:

1  

Use the “buddy system.”  Use more than one “buddy” if 

necessary to move a fellow worker in an emergency.

2  

Both the worker and “buddy” should be equipped with 

self-contained or airline breathing equipment. 

Nitrogen

Nitrogen (an inert gas) is a simple asphyxiate. It will not 

support or sustain life and can produce immediate hazardous 

conditions through the displacement of oxygen. Under high 

pressure this gas may produce unconsciousness even though 

an adequate oxygen supply sufficient for life is present.

Nitrogen vapors in air dilute the concentration of oxygen 

necessary to support or sustain life. Inhalation of high 

concentrations of this gas can cause anoxia, resulting in 

dizziness, nausea, vomiting, or unconsciousness and possibly 

death. Individuals should be prohibited from entering areas 

where the oxygen content is below 19% unless equipped 

with a self-contained breathing apparatus. Unconsciousness 

and death may occur with virtually no warning if the oxygen 

concentration is below approximately 8%. Contact with cold 

nitrogen gas or liquid can cause cryogenic (extreme low 

temperature) burns and freeze body tissue.

Persons suffering from lack of oxygen should be 

immediately moved to areas with normal atmospheres.  

SELF-CONTAINED BREATHING APPARATUS MAY BE 

REQUIRED TO PREVENT ASPHYXIATION OF RESCUE 

WORKERS. Assisted respiration and supplemental oxygen 

should be given if the victim is not breathing. If cryogenic 

liquid or cold boil-off gas contacts worker’s skin or eyes, 

the affected tissue should be flooded or soaked with tepid 

water (105-115ºF or 41-46ºC). DO NOT USE HOT WATER.  

Cryogenic burns that result in blistering or deeper tissue 

freezing should be examined promptly by a physician.

Содержание CryoDoser FleX































Отзывы: