manualshive.com logo in svg

CHART CryoDoser FleX, Руководство по эксплуатации продукта, Страница: 21 / 30

Поделиться
Скачать
CHART CryoDoser FleX Скачать руководство пользователя страница 21

17

Product Manual - CryoDoser FleX

™

 LN

2

 Dosing System

Activating Insta-Purge

The CryoDoser FleX unit has a purge feature that minimizes 

downtime for maintenance and/or nozzle change out without 

draining or shutting down the main LN

2

 supply line.

Nozzle Change Out

1  

Remove the dosing head heater.

2  

Insert the nozzle tool into the nozzle area until the tool 

connects with the nozzle.

3  

Remove the nozzle with the driver in a counter-

clockwise direction.

4  

Once the nozzle is removed, place the new nozzle 

or cleaned nozzle into the nozzle tool and insert in a 

clockwise direction.

Caution!  The dosing head heater may still 

be in operation. Do not expose 

skin to prolonged contact with 

the dosing head heater. The 

maximum temperature of the 

dosing head heater is 150°F 

(65°C).

Caution!  If possible, always perform 

nozzle change out procedures 

before introducing LN

2

 into the 

CryoDoser FleX unit. Failure to 

do so may cause the nozzle to 

unthread and fall out.

Note:

  If the nozzle does not loosen easily, a low 

voltage heat gun may be used to heat 

the 

end

 of the nozzle tool. The tool can then be 

placed over the nozzle to slowly melt any 

ice allowing removal of the nozzle. Repeat 

this process if the nozzle remains stuck.

Nozzle Cleaning

1  

Remove the nozzle from the CryoDoser FleX unit.

2  

Clean the nozzle opening with a very thin wire and 

blow dry nitrogen through it.

3  

Thoroughly dry the nozzle with dry nitrogen gas before 

re-installing.

Caution!  Any moisture left on the nozzle 

will immediately freeze up when 

the nozzle is re-installed which 

may cause the nozzle to unthread 

and fall out.

Service and Maintenance

Image 24

1. 

Unscrew 

old nozzle 

and 

remove

2. 

Replace 

with new 

nozzle

Содержание CryoDoser FleX































Отзывы:

Нет отзывов