Charles FSDC Series Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 13

Charles FSDC Series Скачать руководство пользователя страница 5

LT-FSDC

2

nd

Printing

Page 5 of 13

4.2

Branch Cable Installation or Sealing

Step

Number

Instruction

1

Use the branch port wrench from the bag of
tools to open the branch port nut.

2

Select a grommet of the proper size for the
branch cable (either the grommet from the
branch port or another from the accessory
bag). Run the branch cable through this
grommet and through the nut. Push branch
cable into the FSDC until the cable sheathing
is inside. Note: if the cable is not snug, use
sealing tape.

Push the grommet inward into the branch
cable port. Use the branch port wrench to fully
tighten the branch port nut into position.

3

Guide the strength member under the clamps,
using a Philips screwdriver to tighten the
clamps in place.

Use the 6 mm hose clamps included in the
accessory bag to secure the cables in place.

4

Route the buffer tube once around the trays,
then route into the tray.

Mark the point on the buffer tube where it
enters the tray.

Use a buffer tube slitting tool to remove the
sheathing.

«
...
3
4
5
6
7
...
»

Содержание FSDC Series














Отзывы:

Нет отзывов