Charder MS2500 Скачать руководство пользователя страница 1

MS-2500 

Dual Slope type 

SERVICE MANUAL 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

TABLE OF CONTENTS 

PRECAUTIONS ................................................................................................................................... 1

 

GENERAL INFORMATION .................................................................................................................. 1

 

GENERAL INSPECTION ..................................................................................................................... 1

 

TROUBLESHOOTING ......................................................................................................................... 1

 

SPECIFICATION.................................................................................................................................. 2

 

PANEL / OVERLAY.............................................................................................................................. 3

 

ERROR MESSAGE.............................................................................................................................. 4

 

WIRING................................................................................................................................................ 6

 

LCD FORMAT ...................................................................................................................................... 7

 

CONTROL PANEL ............................................................................................................................... 8

 

LOAD CELL ......................................................................................................................................... 9

 

ZERO COUNT ADJUSTMENT (Dual slope model)............................................................................ 10

 

TROUBLESHOOTING TREE............................................................................................................. 12

 

MS2500 SERVICE MENU CONFIGURATION................................................................................... 13

 

DEFAULT COMPANY SETTINGS ..................................................................................................... 14

 

CALIBRATION PROCEDURE ........................................................................................................... 15

 

PRINT FUNCTION INSTRUCTION.................................................................................................... 17

 

USING PRINT FUNCTION................................................................................................................. 18

 

SCHEMATICS—MAIN BOARD CH-0733 .......................................................................................... 21

 

LAYOUT—MAIN BOARD CH-0733 ................................................................................................... 24

 

SCHEMATICS-POWER BOARD CH-0689 ........................................................................................ 25

 

LAYOUT—POWER BOARD CH-0689............................................................................................... 25

 

SCHEMATICS- JUNCTION BOARD (CH-0525) ................................................................................ 26

 

LAYOUT—JUNCTION BOARD (CH-0525)........................................................................................ 26

 

MS 2500 PARTS & ASSEMBLY ........................................................................................................ 27

 

DP2701, NP- 4444 INDICATOR PARTS & ASSEMBLY .................................................................... 28

 

INSTRUCTION FOR CHARGING AND CONNECTING .................................................................... 30

 

INSTRUCTION FOR REPLACING BATTERY ................................................................................... 31

 

GRAVITY COMPENSATION ............................................................................................................. 32

 

Содержание MS2500




































Отзывы: